Development of a new fracture test to identify the critical energy release rate: The Tensile Flexure test on Notched Specimen

被引：5

作者：

Vandellos, Thomas ^{[1
]}

Hautier, Mathieu ^{[1
]}

Carrere, Nicolas ^{[1
]}

Huchette, Cedric ^{[1
]}

机构：

[1] Off Natl Etud & Rech Aerosp, F-92322 Chatillon, France

来源：

ENGINEERING FRACTURE MECHANICS | 2012年 / 96卷

关键词：

Delamination; Fiber reinforced materials; Toughness testing; Fracture mechanics; I+II INTERLAMINAR FRACTURE; MODE-II; DELAMINATION FRACTURE; COMPOSITES; TOUGHNESS; BEAM;

D O I：

10.1016/j.engfracmech.2012.09.026

中图分类号：

O3 [力学];

学科分类号：

08 ; 0801 ;

摘要：

Delamination is one of the most critical damage mechanisms in laminated composites. A fracture test, referenced in the following as Tensile Flexure test on Notched Specimen, is proposed in this work to characterize the propagation of delamination. After the description of the experimental procedure, experimental results on carbon/epoxy specimens are presented to describe the capabilities and advantages of the test to characterize delamination. Then, a new propagation law is proposed to describe the evolution of the fracture toughness. Finally, a non-deterministic analysis is performed to determine the influence of the measured parameters on the toughness identification. (C) 2012 Elsevier Ltd. All rights reserved.

引用

页码：641 / 655

页数：15

共 49 条

[41] On the Development of New Test Techniques to Measure the Tensile Response of Materials at High and Ultra-high Strain Rates
Zhou, Junyi
Tagarielli, Vito L.
EXPERIMENTAL MECHANICS, 2022, 62 (01) : 151 - 164
[42] On the Development of New Test Techniques to Measure the Tensile Response of Materials at High and Ultra-high Strain Rates
Junyi Zhou
Vito L. Tagarielli
Experimental Mechanics, 2022, 62 : 151 - 164
[43] Modified double cantilever beam test method for mode-I energy release rate of elastic adhesive layers
Morimoto, Tetsuya
Katoh, Hisaya
Ishida, Yuichi
Hara, Eiichi
Kusano, Masahiro
Naito, Kimiyoshi
Watanabe, Makoto
Takagi, Kiyoka
Arai, Keiji
Hasegawa, Koichi
ENGINEERING FRACTURE MECHANICS, 2024, 07
[44] Mode II critical stress intensity factor of wood measured by the asymmetric four-point bending test of single-edge-notched specimen while considering an additional crack length
Yoshihara, Hiroshi
HOLZFORSCHUNG, 2012, 66 (08) : 989 - 992
[45] Delamination behavior and energy release rate evaluation of CFRP/SPCC hybrid laminates under ENF test: Corrected with residual thermal stresses
Muflikhun, Muhammad Akhsin
Higuchi, Ryo
Yokozeki, Tomohiro
Aoki, Takahira
COMPOSITE STRUCTURES, 2020, 236
[46] Analytical solution for the interfacial stress and energy release rate at failure initiation of the three-point bending test (ISO 14679:1997)
Birro, Thiago V.
Paroissien, Eric
Aufray, Maelenn
Lachaud, Frederic
JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2024, 38 (20) : 3876 - 3919
[47] A Theoretical Study of Thin Film Delamination Using Clamped Punch-Loaded Blister Test: Energy Release Rate and Closed-Form Solution
Sun, Jun-yi
Hu, Jian-li
He, Xiao-ting
Zheng, Zhou-lian
Geng, Huan-huan
JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2011, 25 (16) : 2063 - 2080
[48] Discussion of: "Mode II fracture mechanics properties of wood measured by the asymmetric four-point bending test using a single-edge-notched specimen of Hiroshi Yoshihara Eng. Frac. Mech. 75 (2008) 4727-4739"
van der Put, T. A. C. M.
ENGINEERING FRACTURE MECHANICS, 2012, 90 : 172 - 179
[49] Strain energy release rate in combination with reinforcement isotropic solid model (SERIS): A new mixed-mode I/II criterion to investigate fracture behavior of orthotropic materials
Khaji, Zahra
Fakoor, Mahdi
THEORETICAL AND APPLIED FRACTURE MECHANICS, 2021, 113 (113)

← 1 2 3 4 5 →