Optimization of process parameters for producing AA6061/SiC nanocomposites by friction stir processing

被引：103

作者：

Salehi, M. ^{[1
]}

Saadatmand, M. ^{[1
]}

Mohandesi, J. Aghazadeh ^{[1
]}

机构：

[1] Amirkabir Univ Technol, Dept Min & Met Engn, Tehran, Iran

来源：

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA | 2012年 / 22卷 / 05期

关键词：

AA6061/SiC nanocomposites; Taguchi parametric design approach; friction stir processing; analysis of variance; PARTICLE-REINFORCED COMPOSITE; METAL-MATRIX COMPOSITES; MECHANICAL-PROPERTIES; SIC PARTICLES; SURFACE; FABRICATION; MICROSTRUCTURE; GEOMETRY;

D O I：

10.1016/S1003-6326(11)61283-1

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Design of experiment (DOE) was applied to determining the most important factors which influence ultimate tensile strength (UTS) of AA6061/SiC nanocomposites produced by friction stir processing (FSP). Effect of four factors, including rotational speed, transverse speed, tool penetration depth and pin profile, on UTS, was investigated. By Taguchi method, the optimum of process parameters were determined. Analysis of variance shows that the rotational speed is the most influential parameter. The statistical results depict that UTS for threaded pin is larger than that for square pin. Also, the higher the rotational speed and the lower the transverse speed, the higher the UTS.

引用

页码：1055 / 1063

页数：9

共 40 条

[1] [Anonymous], 1990, AM SOC MET HDB MET H, V2
[2] Effects of SiC Particle Size and Process Parameters on the Microstructure and Hardness of AZ91/SiC Composite Layer Fabricated by FSP
Asadi, P.
Givi, M. K. Besharati
Abrinia, K.
Taherishargh, M.
Salekrostam, R.
[J]. JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2011, 20 (09) : 1554 - 1562
[3] Producing of AZ91/SiC composite by friction stir processing (FSP)
Asadi, Parviz
Faraji, Ghader
Besharati, Mohammad K.
[J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2010, 51 (1-4) : 247 - 260
[4] Effect of rotational speed and probe profile on microstructure and hardness of AZ31/Al2O3 nanocomposites fabricated by friction stir processing
Azizieh, M.
Kokabi, A. H.
Abachi, P.
[J]. MATERIALS & DESIGN, 2011, 32 (04): : 2034 - 2041
[5] On the role of processing parameters in producing Cu/SiC metal matrix composites via friction stir processing: Investigating microstructure, microhardness, wear and tensile behavior
Barmouz, Mohsen
Givi, Mohammad Kazem Besharati
Seyfi, Javad
[J]. MATERIALS CHARACTERIZATION, 2011, 62 (01) : 108 - 117
[6] Effect of friction stir processing (FSP) on microstructure and properties of Al-TiC in situ composite
Bauri, Ranjit
Yadav, Devinder
Suhas, G.
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (13-14): : 4732 - 4739
[7] The influence of stirrer geometry on bonding and mechanical properties in friction stir welding process
Boz, M
Kurt, A
[J]. MATERIALS & DESIGN, 2004, 25 (04) : 343 - 347
[8] Effect of Processing Parameters on Microstructure and Mechanical Properties of an Al-Al11Ce3-Al2O3 In-Situ Composite Produced by Friction Stir Processing
Chen, C. F.
Kao, P. W.
Chang, L. W.
Ho, N. J.
[J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2010, 41A (02): : 513 - 522
[9] On the forming mechanism of banded structures in aluminium alloy friction stir welds
Chen, Z. W.
Cui, S.
[J]. SCRIPTA MATERIALIA, 2008, 58 (05) : 417 - 420
[10] Influences of tool pin profile and welding speed on the formation of friction stir processing zone in AA2219 aluminium alloy
Elangovan, K.
Balasubramanian, V.
[J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 200 (1-3) : 163 - 175

← 1 2 3 4 →