Experimental device for tribological measurement aspects in deep drawing process

被引：14
作者：
Roizard, X. [1 ]
Pothier, J. M. [1 ,2 ]
Hihn, J. Y. [2 ]
Monteil, G. [1 ]
机构：
[1] ENSMM, LMS, F-25030 Besancon, France
[2] IUT, LCMI, F-25000 Besancon, France
来源：
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 2009年 / 209卷 / 03期
关键词：
Deep drawing; Tribology; Strip drawing; Temperature contact; Bulk deformation; Adhesive junction properties; TENSION FRICTION TEST; VELOCITY ACCOMMODATION; STAINLESS-STEEL; SHEETS; SIMULATION; COMPONENT;
D O I：
10.1016/j.jmatprotec.2008.03.023
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The purpose of this paper is to improve strip drawing test in order to simulate sheet/tool contact conditions during a stamping operation. An original multi-pass strip drawing test in cylinder/sheet/cylinder contact geometry is presented and we emphasize the influence of certain factors rarely taken into account in the experimental simulation. In particular, we present examples where the bulk plastic deformation and the tools average temperature influence the level of friction and the sheet surface asperities flattening. To try to readjust the friction evolutions with the modifications of surface microgeometry, the tribometer is equipped with various measurements of relative sheet/tool displacement, including or not the stiffness machine and the stiffness of the contact. This was made possible by a potentiometric measurement where the tool plays the part of potentiometer and sheet that of the track, coupled to a measurement using a LVDT sensor. (C) 2008 Elsevier B.V All rights reserved.
引用
收藏
页码：1220 / 1230
页数：11
相关论文
共 22 条
[11]   Surface asperity deformation under bulk plastic straining conditions [J].
Kimura, Y ;
Childs, THC .
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 1999, 41 (03) :283-307
[12]   Factors influencing friction in steel sheet forming [J].
Matuszak, A .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 106 (1-3) :250-253
[13]  
Milner D.R., 1962, Metallurgical Reviews, V7, P433, DOI DOI 10.1179/MTLR.1962.7.1.433
[14]   Process design for hydroforming of lightweight metal sheets at elevated temperatures [J].
Novotny, S ;
Geiger, M .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2003, 138 (1-3) :594-599
[15]   Influence of sliding direction and sliding speed on the microhydrodynamic lubrication component of aluminium mill-finish sheets [J].
Roizard, X ;
Raharijaona, F ;
von Stebut, J ;
Belliard, P .
TRIBOLOGY INTERNATIONAL, 1999, 32 (12) :739-747
[16]   SURFACE ASPERITY FLATTENING IN SHEET-METAL FORMING - A 3-D RELOCATION STYLUS PROFILOMETRIC STUDY [J].
ROIZARD, X ;
VONSTEBUT, J .
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 1995, 35 (02) :169-175
[17]  
ROIZARD X, 1993, MATERIAUX TECHNIQUES, P45
[18]   Experimental set-up and data processing of the radial strip-drawing friction test [J].
Sniekers, RJJM ;
Smits, HAA .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1997, 66 (1-3) :216-223
[19]  
SULONEN M, 1981, P IDDRG WORK GROUP M
[20]   Simulation of transfer layer formation in strip drawing of stainless steel [J].
Sutcliffe, MPF ;
Le, HR ;
Farrugia, D .
WEAR, 2003, 254 (5-6) :523-531
123