Improvement of the rotary draw bending process in rectangular tubes by using internal fluid pressure

被引:16
作者
Zardoshtian, Ali [1 ]
Sabet, Hossein [1 ]
Elyasi, Majid [1 ]
机构
[1] Babol Noshirvani Univ Technol, Fac Mech Engn, PO 484, Mazandaran, Babol, Iran
关键词
Rotary draw bending; Rectangular tubes; Fluid internal pressure; Defects; LIMIT;
D O I
10.1007/s00170-017-1255-4
中图分类号
TP [自动化技术、计算机技术];
学科分类号
0812 ;
摘要
The rotary draw bending has been conducted in square sections usually through techniques such as using the mandrel and wiper, which are mainly associated with inevitable defects such as wrinkling, thinning, folding, tearing, sagging, and cross-sectional distortion in the bending area. In this research, the improvement in the bending process of Al6063 rectangular tubes has been evaluated experimentally and numerically by applying the internal fluid pressure. Since the rectangular tube sealing is difficult in practice, designing a sealing system suitable for both ends of the tube has been tried. This was done to investigate the effect of different fluid pressures and without fluid pressure at the bending ratio of 3. Also, the amount of increasing in the thickness and wrinkling of the intrados area and decreasing in the thickness and sagging of the bent tube extrados is examined. The results showed that wrinkling, sagging, and cross-sectional distortion in the bending area has been reduced significantly. As a consequence, at a certain pressure, those kinds of defects almost disappeared due to the strain distribution caused by stress arising on the internal surface of the tube.
引用
收藏
页码:697 / 705
页数:9
相关论文
共 11 条
[1]  
[Anonymous], 1990, METALS HDB, V2
[2]   Predicting the bending limit of AA8112 tubes using necking criterion in manufacturing of bent tubes [J].
Elyasi, Majid ;
Paluch, Mehrdad ;
Hosseinzadeh, Morteza .
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 88 (9-12) :3307-3318
[3]   Deformation behaviors of thin-walled tube in rotary draw bending under push assistant loading conditions [J].
Li, H. ;
Yang, H. ;
Zhan, M. ;
Kou, Y. L. .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2010, 210 (01) :143-158
[4]   Increasing the Working Limit of Extruded Aluminum Tubes During Draw Bending by Introducing a Wiper Die [J].
Okude, Yusuke ;
Sakaki, Shuji ;
Yoshihara, Shoichiro ;
MacDonald, Bryan J. .
MATERIALS TRANSACTIONS, 2012, 53 (05) :875-878
[5]   A chain link mandrel for rotary draw bending: experimental and finite element study of operation [J].
Salem, Mohammad ;
Farzin, Mahmoud ;
Kadkhodaei, Mahmoud ;
Nakhaei, Mohsen .
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 79 (5-8) :1071-1080
[6]  
Soleimani J, AMIRKABIR IN PRESS
[7]  
Soleimani J., 2016, MODARES MECH ENG, V16, P287
[8]   Countermeasures against undesirable phenomena in the draw-bending process for extruded square tubes [J].
Utsumi, N ;
Sakaki, S .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2002, 123 (02) :264-269
[9]   Study on varying curvature push-bending technique of rectangular section tube [J].
Xiao, X. T. ;
Liao, Y. J. ;
Sun, Y. S. ;
Zhang, Z. R. ;
Kerdeyev, Yu P. ;
Neperish, R. I. .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 187 :476-479
[10]   Cross-sectional distortion behaviors of thin-walled rectangular tube in rotary-draw bending process [J].
Zhao Gang-yao ;
Liu Yu-li ;
Yang He ;
Lu Cai-hong .
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2010, 20 (03) :484-489