Effects of Non-Electrical Parameters on Material Removal Rate of High-Speed Small Hole EDM Drilling

被引：3
|
作者：
Cao, M. R. [1 ]
Wang, Y. Q. [1 ]
Yang, S. C. [1 ]
Yang, S. Q. [1 ]
Li, W. H. [1 ]
机构：
[1] Taiyuan Univ Technol, Coll Mech Engn, Taiyuan Shanxi 030024, Peoples R China
来源：
SURFACE FINISHING TECHNOLOGY AND SURFACE ENGINEERING | 2008年 / 53-54卷
关键词：
Small hole; EDM; Material removal rate; Non-Electrical parameters; DISCHARGE; ELECTRODE;
D O I：
10.4028/www.scientific.net/AMR.53-54.403
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The selection of manufacturing conditions is very important in manufacturing processes as these ones determine the material removal rate (MRR) of the so-obtained parts. So in this paper, based on the brief introduction of the experimental principle and the high-speed small hole EDM drilling system, effects of non-electrical parameters on MRR are discussed in detail. The relationships between MRR and these factors are also analyzed. The conclusion can provide an important reference for production in practice.
引用
收藏
页码：403 / 407
页数：5
相关论文
共 13 条
  • [1] Thermal Modeling of the Material Removal Rate for High-speed Small Hole EDM Drilling Using the Computational Fluid Dynamics Method
    Wang, Yanqing
    Bai, Jicheng
    Guo, Yongfeng
    Huang, He
    Liu, Jinchun
    PROCEEDINGS OF THE 16TH INTERNATIONAL SYMPOSIUM ON ELECTROMACHINING, 2010, 2010, : 705 - 710
  • [2] Break-out detection for high-speed small hole drilling EDM based on machine learning
    Xia Weiwen
    Wang Junqi
    Zhao Wansheng
    19TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING, 2018, 68 : 569 - 574
  • [3] Numerical Simulation of Liquid-Solid Two-Phase Flow Field in Discharge Gap of High-Speed Small Hole EDM Drilling
    Wang, Y. Q.
    Cao, M. R.
    Yang, S. Q.
    Li, W. H.
    SURFACE FINISHING TECHNOLOGY AND SURFACE ENGINEERING, 2008, 53-54 : 409 - 414
  • [4] Novel methods for high-speed observation of material removal and molten pool movement in EDM
    Yue, Xiaoming
    Yang, Xiaodong
    Li, Qi
    Li, Xiaohui
    PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY, 2020, 66 : 295 - 305
  • [5] Effects of non-electrical parameters on profile accuracies and surface characteristics during wire-EDM of titanium alloy
    Kirwin, Roan M.
    Jahan, Muhammad P.
    MACHINING SCIENCE AND TECHNOLOGY, 2021, 25 (06) : 1031 - 1052
  • [6] Stability-based selection of cutting parameters to increase material removal rate in high-speed machining process
    Cao, Hongrui
    Zhou, Kai
    Chen, Xuefeng
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2016, 230 (02) : 227 - 240
  • [7] Effect of Wire-EDM Machining Parameters on Surface Roughness and Material Removal Rate of High Strength Armor Steel
    Bobbili, Ravindranadh
    Madhu, V.
    Gogia, A. K.
    MATERIALS AND MANUFACTURING PROCESSES, 2013, 28 (04) : 364 - 368
  • [8] Effects of the reciprocating parameters of the carrier on material removal rate and non-uniformity in CMP
    Wang Cailing
    Kang Renke
    Jin Zhuji
    Guo Dongming
    JOURNAL OF SEMICONDUCTORS, 2010, 31 (12)
  • [9] Analysis of Effects of Cutting Parameters of Wire Electrical Discharge Machining on Material Removal Rate and Surface Integrity
    Tonday, H. R.
    Tigga, A. M.
    5TH NATIONAL CONFERENCE ON PROCESSING AND CHARACTERIZATION OF MATERIALS, 2016, 115
  • [10] Investigation of Wire-Cut EDM parameters for machining 2304 duplex stainless steel: effects on material removal rate, surface roughness, and tool wear
    Radhakrishnan, Kamalakkannan
    Kesavalu, Rajmohan
    MATERIA-RIO DE JANEIRO, 2025, 30
12