Investigation on strain dependence of metadynamic recrystallization behaviors of GH4169 superalloy

被引:40
作者
Chen, Xiao-Min [1 ,3 ]
Lin, Y. C. [1 ,2 ,3 ]
Li, Xin-He [1 ,2 ,3 ]
Chen, Ming-Song [1 ,3 ]
Yuan, Wu-Quan [1 ,3 ]
机构
[1] Cent S Univ, Sch Mech & Elect Engn, Changsha 410083, Hunan, Peoples R China
[2] Cent S Univ, Light Alloy Res Inst, Changsha 410083, Hunan, Peoples R China
[3] State Key Lab High Performance Complex Mfg, Changsha 410083, Hunan, Peoples R China
关键词
Alloy; Hot deformation; Strain dependence; Metadynamic recrystallization; NICKEL-BASED SUPERALLOY; HOT DEFORMATION-BEHAVIOR; ULTRASUPERCRITICAL ROTOR STEEL; WORK-HARDENING CHARACTERISTICS; LOW-CYCLE FATIGUE; MICROSTRUCTURAL EVOLUTION; DYNAMIC RECRYSTALLIZATION; PROCESSING MAP; BASE SUPERALLOY; ELEVATED-TEMPERATURE;
D O I
10.1016/j.vacuum.2017.11.021
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The metadynamic recrystallization (MDRX) behaviors of a solid-solution GH4169 superalloy were studied by two-pass hot compression tests. The effects of pre-strain (deformation degree of the first pass) on MDRX behaviors were analyzed. Results show that the MDRX behaviors intensely depend on the pre-strain. The MDRX fraction first increases and then drops with the increased pre-strain. This is because a relatively large pre-strain can facilitate the nucleation of dynamic recrystallization (DRX) grains, which promotes the subsequent MDRX behaviors. However, due to the decreased stored deformation energy at relatively high pre-strain, the number of DRX grains cannot continuously increases. Thus, the MDRX fraction is reduced with the further increase of pre-strain. The segmented MDRX kinetics models were proposed and validated to describe the significant strain dependence of MDRX behaviors. (C) 2017 Elsevier Ltd. All rights reserved.
引用
收藏
页码:1 / 11
页数:11
相关论文
共 48 条
[1]  
Azarbarmasa M., 2017, SIMUL MATER SCI ENG, V25
[2]   Static Recrystallization of 30Cr2Ni4MoV Ultra-Super-Critical Rotor Steel [J].
Chen, Fei ;
Sui, Dashan ;
Cui, Zhenshan .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2014, 23 (08) :3034-3041
[3]   Recrystallization of 30Cr2Ni4MoV ultra-super-critical rotor steel during hot deformation. Part III: Metadynamic recrystallization [J].
Chen, Fei ;
Cui, Zhenshan ;
Sui, Dashan ;
Fu, Bo .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 540 :46-54
[4]   Low cycle fatigue and creep-fatigue interaction behavior of nickel-base superalloy GH4169 at elevated temperature of 650°C [J].
Chen, G. ;
Zhang, Y. ;
Xu, D. K. ;
Lin, Y. C. ;
Chen, X. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 655 :175-182
[5]   Hot Deformation Behaviors and Processing Maps of 2024 Aluminum Alloy in As-cast and Homogenized States [J].
Chen, Liang ;
Zhao, Guoqun ;
Gong, Jie ;
Chen, Xiaoxue ;
Chen, Mengmeng .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2015, 24 (12) :5002-5012
[6]   EBSD study of grain growth behavior and annealing twin evolution after full recrystallization in a nickel-based superalloy [J].
Chen, Xiao-Min ;
Lin, Y. C. ;
Wu, Fan .
JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 724 :198-207
[7]   Microstructural evolution of a nickel-based superalloy during hot deformation [J].
Chen, Xiao-Min ;
Lin, Y. C. ;
Chen, Ming-Song ;
Li, Hong-Bin ;
Wen, Dong-Xu ;
Zhang, Jin-Long ;
He, Min .
MATERIALS & DESIGN, 2015, 77 :41-49
[8]   Dynamic recrystallization behavior of a typical nickel-based superalloy during hot deformation [J].
Chen, Xiao-Min ;
Lin, Y. C. ;
Wen, Dong-Xu ;
Zhang, Jin-Long ;
He, Min .
MATERIALS & DESIGN, 2014, 57 :568-577
[9]   Metadynamic recrystallization behavior and workability characteristics of HR3C austenitic heat-resistant stainless steel with processing map [J].
Cheng, Yang ;
Du, Huayun ;
Wei, Yinghui ;
Hou, Lifeng ;
Liu, Baosheng .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2016, 235 :134-142
[10]   An investigation on determination of flow curves at room temperature and under forming conditions [J].
Fereshteh-Saniee, F. ;
Fatehi-Sichani, F. .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2006, 177 (1-3) :478-482