Microstructure and Solute Segregation around the Melt-Pool Boundary of Orientation-Controlled 316L Austenitic Stainless Steel Produced by Laser Powder Bed Fusion

被引:12
作者
Sato, Kazuhisa [1 ]
Takagi, Shunya [1 ]
Ichikawa, Satoshi [1 ]
Ishimoto, Takuya [2 ,3 ,4 ]
Nakano, Takayoshi [2 ,3 ]
机构
[1] Osaka Univ, Res Ctr Ultrahigh Voltage Electron Microscopy, 7-1 Mihogaoka, Ibaraki 5670047, Japan
[2] Osaka Univ, Grad Sch Engn, Div Mat & Mfg Sci, 2-1 Yamadaoka, Suita 5650871, Japan
[3] Osaka Univ, Anisotrop Design & Addit Mfg Res Ctr, 2-1 Yamadaoka, Suita 5650871, Japan
[4] Univ Toyama, Aluminium Res Ctr, 3190 Gofuku, Toyama 9308555, Japan
关键词
additive manufacturing; laser powder-bed fusion; cellular microstructure; solidification segregation; transmission electron microscopy; CORROSION;
D O I
10.3390/ma16010218
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
For this article, we studied the microstructure and solute segregation seen around the melt pool boundary of orientation-controlled 316L austenitic stainless steel produced by laser powder bed fusion, using transmission electron microscopy and energy-dispersive x-ray spectroscopy. We found that the solidification cellular microstructures could be visualized with the aid of solute segregation (Cr and Mo) during solidification. Mn-Si-O inclusions (10-15 nm in diameter) were distributed along the lamellar boundaries, as well as in the dislocation cell walls. It is believed that the grain growth of the inclusions can be effectively suppressed by rapid quenching during the laser powder-bed fusion process. A thin region without cellular microstructures was observed at the melt-pool boundary. The cellular spacing widened near the bottom of the melt-pool boundary, owing to the decrease in the cooling rate. Atomic-structure analysis at the lamellar boundary by high-resolution transmission electron microscopy revealed a local interfacial structure, which is complementary to the results of electron back-scatter diffraction.
引用
收藏
页数:10
相关论文
共 50 条
[41]   Tailoring the microstructural and mechanical properties of 316L stainless steel manufactured by laser powder bed fusion [J].
Liu, Wei ;
Liu, Cheng-song ;
Wang, Yong ;
Zhang, Hua ;
Li, Lie ;
Lu, Yuan-yuan ;
Xiong, Li ;
Ni, Hong-wei .
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 25 :7389-7405
[42]   Two-steps electrochemical polishing of laser powder bed fusion 316l stainless steel [J].
Zhu, Haitao ;
Rennie, Allan ;
Li, Ruifeng ;
Tian, Yingtao .
SURFACES AND INTERFACES, 2022, 35
[43]   On the use of slurry as an alternative to dry powder for laser powder bed fusion of 316L stainless steel [J].
Meyers, Sebastian ;
Gurung, Kopila ;
Kinds, Yannis ;
Van Hooreweder, Brecht .
ADDITIVE MANUFACTURING LETTERS, 2024, 11
[44]   Evolution of Creep Damage of 316L Produced by Laser Powder Bed Fusion [J].
Ulbricht, Alexander ;
Calderon, Luis Alexander Avila ;
Sommer, Konstantin ;
Mohr, Gunther ;
Evans, Alexander ;
Skrotzki, Birgit ;
Bruno, Giovanni .
ADVANCED ENGINEERING MATERIALS, 2023, 25 (12)
[45]   Crystallographic-orientation-dependent tensile behaviours of stainless steel 316L fabricated by laser powder bed fusion [J].
Wang, Xianglong ;
Muniz-Lerma, Jose Alberto ;
Shandiz, Mohammad Attarian ;
Sanchez-Mata, Oscar ;
Brochu, Mathieu .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 766
[46]   Crystallographic orientation dependence of Charpy impact behaviours in stainless steel 316L fabricated by laser powder bed fusion [J].
Wang, Xianglong ;
Sanchez-Mata, Oscar ;
Atabay, Sila Ece ;
Muniz-Lerma, Jose Alberto ;
Shandiz, Mohammad Attarian ;
Brochu, Mathieu .
ADDITIVE MANUFACTURING, 2021, 46
[47]   Effect of process parameters on the microstructure, tensile strength and productivity of 316L parts produced by laser powder bed fusion [J].
Leicht, A. ;
Rashidi, M. ;
Klement, U. ;
Hryha, E. .
MATERIALS CHARACTERIZATION, 2020, 159
[48]   Influence of wall thickness on microstructure and mechanical properties of thin-walled 316L stainless steel produced by laser powder bed fusion [J].
Wrobel, R. ;
Del Guidice, L. ;
Scheel, P. ;
Abando, N. ;
Maeder, X. ;
Vassiliou, M. ;
Hosseini, E. ;
Spolenak, R. ;
Leinenbach, C. .
MATERIALS & DESIGN, 2024, 238
[49]   Influence of laser powder bed fusion processing parameters on corrosion behaviour of 316L stainless steel in nitric acid [J].
Puga, Beatriz ;
Lomello, Fernando ;
Boussac, Emeline ;
Chniouel, Aziz ;
Fouchereau, Alexis ;
Laghoutaris, Pierre ;
Maskrot, Hicham .
METALLURGICAL RESEARCH & TECHNOLOGY, 2022, 119 (05)
[50]   Influence of the Processing Parameters on the Microstructure and Mechanical Properties of 316L Stainless Steel Fabricated by Laser Powder Bed Fusion [J].
Barrionuevo, German Omar ;
Ramos-Grez, Jorge Andres ;
Sanchez-Sanchez, Xavier ;
Zapata-Hidalgo, Daniel ;
Mullo, Jose Luis ;
Puma-Araujo, Santiago D. .
JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING, 2024, 8 (01)