Investigation of fracture parameters for a surface-cracked multi-pass T-joint considering welding residual stress

被引：5

作者：

Gadallah, Ramy ^{[1
]}

Murakawa, Hidekazu ^{[2
]}

Shibahara, Masakazu ^{[1
]}

机构：

[1] Osaka Metropolitan Univ, Grad Sch Engn, Osaka, Japan

[2] Osaka Univ, Joining & Welding Res Inst, Osaka, Japan

来源：

THEORETICAL AND APPLIED FRACTURE MECHANICS | 2023年 / 127卷

关键词：

Welding residual stress; Final weld pass location; Surface crack; mixed-mode SIFs; Loading type; FEM; INTENSITY FACTOR; WELDED-JOINT; MAGNIFICATION FACTORS; DISTORTION; PREDICTION; MODE; COMPUTATION; STEEL; DEFORMATION; PROPAGATION;

D O I：

10.1016/j.tafmec.2023.104080

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

A numerical simulation procedure was carried out to evaluate the fracture parameters for a surface-cracked thick-plate T-joint considering welding residual stress (WRS) effect. Welding calculation was performed to simulate the welded joint then the results were verified against the experiment taken from the literature. The effect of the location of the final weld pass on WRS distribution was also analyzed numerically. Stress analyses were conducted using an intact T-joint model under different mechanical loading patterns, to determine the location of the hot spot stress and thereafter the location of the surface crack. Subsequently, the fracture parameters were thoroughly addressed under different conditions including external loading only and a combination of external loading and WRS. The effect of weld angle on the behavior of fracture parameters was also discussed. The numerical calculations succeeded in explaining the fundamental fracture characteristics of a multi-pass T-joint with a surface crack.

引用

页数：18

共 38 条

[1] Prediction of weld toe magnification factors for semi-elliptical cracks in T-butt joints [J].

Bowness, D ;

Lee, MMK .

INTERNATIONAL JOURNAL OF FATIGUE, 2000, 22 (05) :369-387

[2] Parametric equations for T-butt weld toe stress intensity factors [J].

Brennan, FP ;

Dover, WD ;

Karé, RF ;

Hellier, AK .

INTERNATIONAL JOURNAL OF FATIGUE, 1999, 21 (10) :1051-1062

[3]

BSI Standards Publication, 2015, BS 7910

[4] Experimental and numerical investigations of welding distortion induced by CO2 gas arc welding in thin-plate bead-on joints [J].

Deng, Dean ;

Zhou, Yijun ;

Bi, Tao ;

Liu, Xiaozhan .

MATERIALS & DESIGN, 2013, 52 :720-729

[5] Influence of deposition sequence on welding residual stress and deformation in an austenitic stainless steel J-groove welded joint [J].

Deng, Dean .

MATERIALS & DESIGN, 2013, 49 :1022-1033

[6] FEM prediction of welding residual stress and distortion in carbon steel considering phase transformation effects [J].

Deng, Dean .

MATERIALS & DESIGN, 2009, 30 (02) :359-366

[7] Investigation of the Residual Stress in a Multi-Pass T-Welded Joint Using Low Transformation Temperature Welding Wire [J].

Feng, Zhongyuan ;

Ma, Ninshu ;

Tsutsumi, Seiichiro ;

Lu, Fenggui .

MATERIALS, 2021, 14 (02) :1-15

[8] WELD MAGNIFICATION FACTORS FOR SEMIELLIPTIC SURFACE CRACKS IN FILLET WELDED T-BUTT JOINT MODELS [J].

FU, B ;

HASWELL, JV ;

BETTESS, P .

INTERNATIONAL JOURNAL OF FRACTURE, 1993, 63 (02) :155-171

[9] Investigation of thickness and welding residual stress effects on fatigue crack growth [J].

Gadallah, Ramy ;

Murakawa, Hidekazu ;

Shibahara, Masakazu .

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH, 2023, 201

[10] Accurate evaluation of fracture parameters for a surface-cracked tubular T-joint taking welding residual stress into account [J].

Gadallah, Ramy ;

Tsutsumi, Seiichiro ;

Tanaka, Satoyuki ;

Osawa, Naoki .

MARINE STRUCTURES, 2020, 71 (71)

← 1 2 3 4 →