Fatigue behavior of selective laser melted 316L stainless steel: Experiments and modeling

被引：5

作者：

Tian, Xuanxin ^{[1
]}

Li, Qiubo ^{[1
]}

Zhao, Guicheng ^{[1
]}

Qu, Zhaoliang ^{[1
]}

Ai, Shigang ^{[1
]}

机构：

[1] Beijing Inst Technol, Inst Adv Struct Technol, Beijing 100081, Peoples R China

来源：

ENGINEERING FRACTURE MECHANICS | 2024年 / 298卷

基金：

中国国家自然科学基金;

关键词：

Additive manufacturing; 316L stainless steel; High cycle fatigue; Low cycle fatigue; Fracture behavior; HIGH-CYCLE FATIGUE; RESIDUAL-STRESSES; DAMAGE EVOLUTION; FRETTING FATIGUE; LIFE PREDICTION; PERFORMANCE; MECHANICS;

D O I：

10.1016/j.engfracmech.2024.109942

中图分类号：

O3 [力学];

学科分类号：

08 ; 0801 ;

摘要：

Selective laser melting (SLM) is extensively applied in fabricating 316L stainless steel structures. In this study, a series of mechanical tests were conducted on SLM 316L stainless steel, including tensile testing, high cycle fatigue (HCF) testing at various stress ratios and mean stresses, and low cycle fatigue (LCF) testing at different strain amplitudes. A efficient method of processing CT images was employed to analyze the porosity and fatigue failure behavior of material. Additionally, we proposed an elasto-plastic fatigue damage evolution model takes porosity into account, with relevant parameters determined through experiments. The predicted life under experimental conditions was calculated using the UMAT and DISP subroutines in ABAQUS software. Results indicate that mean stress significantly reduces fatigue strength, and irregularly shaped pores are the primary cause of material failure and reduction in strength. The predicted life of the elasto-plastic fatigue damage model is in good agreement with the experimental results. These results have important implications for the design and maintenance of SLM 316L stainless steel structures.

引用

页数：19

共 47 条

[1] Kinematic hardening model suitable for ratchetting with steady-state [J].

Abdel-Karim, M ;

Ohno, N .

INTERNATIONAL JOURNAL OF PLASTICITY, 2000, 16 (3-4) :225-240

[2] Additive manufacturing: Challenges, trends, and applications [J].

Abdulhameed, Osama ;

Al-Ahmari, Abdulrahman ;

Ameen, Wadea ;

Mian, Syed Hammad .

ADVANCES IN MECHANICAL ENGINEERING, 2019, 11 (02)

[3] Steels in additive manufacturing: A review of their microstructure and properties [J].

Bajaj, P. ;

Hariharan, A. ;

Kini, A. ;

Kuernsteiner, P. ;

Raabe, D. ;

Jaegle, E. A. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 772

[4]

Basquin O.H., 1910, Am. Soc. Test. Mater. Proc., P625, DOI DOI 10.4236/MSA.2011.212231

[5]

Beard W, 2019, SOLID FREEFORM FABRI, P2144

[6] Fracture and fatigue in additively manufactured metals [J].

Becker, Thorsten Hermann ;

Kumar, Punit ;

Ramamurty, Upadrasta .

ACTA MATERIALIA, 2021, 219

[7] Assessment of the effect of isolated porosity defects on the fatigue performance of additive manufactured titanium alloy [J].

Biswal, Romali ;

Syed, Abdul Khadar ;

Zhang, Xiang .

ADDITIVE MANUFACTURING, 2018, 23 :433-442

[8] A NON-LINEAR CONTINUOUS FATIGUE DAMAGE MODEL [J].

CHABOCHE, JL ;

LESNE, PM .

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 1988, 11 (01) :1-17

[9]

Coffin LF., 1954, Trans ASME, V13, P1991

[10] Effects of defects on mechanical properties in metal additive manufacturing: A review focusing on X-ray tomography insights [J].

du Plessis, Anton ;

Yadroitsava, Ina ;

Yadroitsev, Igor .

MATERIALS & DESIGN, 2020, 187

← 1 2 3 4 5 →