The effect of heat treatment on the microstructure and mechanical properties of multilayer AA6061 alloy fabricated by additive friction stir deposition

被引：15

作者：

Chen, Lan ^{[1
]}

Li, Yunze ^{[1
]}

Lu, Linkai ^{[1
]}

Yang, Zhiwei ^{[1
]}

Ren, Xudong ^{[1
]}

Zhang, Xinzhou ^{[1
]}

机构：

[1] Jiangsu Univ, Sch Mech Engn, Zhenjiang 212013, Peoples R China

来源：

MATERIALS TODAY COMMUNICATIONS | 2024年 / 38卷

关键词：

Additive friction stir deposition; Aluminum alloy; Microstructure evolution; Mechanical behavior; EVOLUTION; AL; CU;

D O I：

10.1016/j.mtcomm.2024.108078

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Multilayer AA6061 aluminum alloy components were successfully fabricated by the additive friction stir deposition (AFSD). The effect of heat treatment on the microstructure and mechanical behavior of the aluminum alloy components was studied. Due to dynamic recrystallization, AFSD AA6061 sample presented a 93.2% average reduction in grain size as compared to base material (BM) (similar to 39.13 mu m). Abnormal grain growth was observed in the AFSD-HT sample, and the average grain size of AFSD-HT sample was 592 mu m. There was an occurrence of texture formation in the AFSD and AFSD-HT samples, mainly due to severe shear deformation during AFSD process. The maximum texture density of AFSD-HT sample was increased to 17.84. In the BM sample, apart from the beta" strengthening phases, hard-brittle intermetallic compounds of Al5FeSi aggregated along the boundaries of the coarser grains. Due to the high temperature generated during the process of AFSD, the beta" strengthening phases dissolved into the matrix, and significantly reduced the strength and hardness. After heat treatment, the AFSD AA6016 alloy recovered 18% of its strength at a loss of 2.8% ductility. High density beta" strengthening phases precipitated, resulting in increased strength and hardness.

引用

页数：12

共 40 条

[1] Effect of short-term annealing on the microstructures and flow properties of an Al-1% Mg alloy processed by high-pressure torsion [J].

Andreau, Olivier ;

Gubicza, Jeno ;

Zhang, Nian Xian ;

Huang, Yi ;

Jenei, Peter ;

Langdon, Terence G. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 615 :231-239

[2] Influence of Grain Refinement and Microstructure on Fatigue Behavior for Solid-State Additively Manufactured Al-Zn-Mg-Cu Alloy [J].

Avery, D. Z. ;

Phillips, B. J. ;

Mason, C. J. T. ;

Palermo, M. ;

Williams, M. B. ;

Cleek, C. ;

Rodriguez, O. L. ;

Allison, P. G. ;

Jordon, J. B. .

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2020, 51 (06) :2778-2795

[3] Precipitation in AA6063 produced from swarf using additive friction stir deposition [J].

Babaniaris, Steven ;

Jiang, Lu ;

Varma, Ramesh Kumar ;

Farabi, Ehsan ;

Dorin, Thomas ;

Barnett, Matthew ;

Fabijanic, Daniel .

ADDITIVE MANUFACTURING LETTERS, 2022, 3

[4] The effect of solutionizing and artificial aging on the microstructure and mechanical properties in solid-state additive manufacturing of precipitation hardened Al-Mg-Si alloy [J].

Beck, S. C. ;

Rutherford, B. A. ;

Avery, D. Z. ;

Phillips, B. J. ;

Rao, H. ;

Rekha, M. Y. ;

Brewer, L. N. ;

Allison, P. G. ;

Jordon, J. B. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 819

[5] Microstructure evolution of 316L stainless steel during solid-state additive friction stir deposition [J].

Beladi, Hossein ;

Farabi, Ehsan ;

Hodgson, Peter D. ;

Barnett, Matthew R. ;

Rohrer, Gregory S. ;

Fabijanic, Daniel .

PHILOSOPHICAL MAGAZINE, 2022, 102 (07) :618-633

[6] Microstructure evolution, mechanical properties, and strengthening mechanism of TiC reinforced Inconel 625 nanocomposites fabricated by selective laser melting [J].

Chen, Lan ;

Sun, Yuzhou ;

Li, Lin ;

Ren, Xudong .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 792

[7] Effect of heat treatment on the microstructure and high temperature oxidation behavior of TiC/Inconel 625 nanocomposites fabricated by selective laser melting [J].

Chen, Lan ;

Sun, Yuzhou ;

Li, Lin ;

Ren, Xudong .

CORROSION SCIENCE, 2020, 169

[8] Six decades of the Hall-Petch effect - a survey of grain-size strengthening studies on pure metals [J].

Cordero, Z. C. ;

Knight, B. E. ;

Schuh, C. A. .

INTERNATIONAL MATERIALS REVIEWS, 2016, 61 (08) :495-512

[9] Joining of 1060/6063 aluminum alloys based on porthole die extrusion process [J].

Fan, Xiangkun ;

Chen, Liang ;

Chen, Gaojin ;

Zhao, Guoqun ;

Zhang, Cunsheng .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2017, 250 :65-72

[10] Characterization of Inconel 625 fabricated using powder-bed-based additive manufacturing technologies [J].

Gonzalez, J. A. ;

Mireles, J. ;

Stafford, S. W. ;

Perez, M. A. ;

Terrazas, C. A. ;

Wicker, R. B. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2019, 264 :200-210

← 1 2 3 4 →