Study of Low-Pressure Cold Spray Additive Manufacturing: Investigation of Kinematic Spray Parameters on Deposition and Properties

被引：6

作者：

Li, Wenbo ^{[1
]}

Wu, Hongjian ^{[2
]}

Verdy, Christophe ^{[1
]}

Costil, Sophie ^{[1
]}

Liao, Hanlin ^{[1
]}

Deng, Sihao ^{[1
]}

机构：

[1] Univ Bourgogne Franche Comte, UTBM, CNRS, ICB UMR 6303, Belfort, France

[2] Helmut Schmidt Univ, Univ Fed Armed Forces Hamburg, Inst Mat Technol, Hamburg, Germany

来源：

3D PRINTING AND ADDITIVE MANUFACTURING | 2023年 / 10卷 / 06期

关键词：

cold spray; low pressure; additive manufacturing; spraying distance; velocity; scanning pass; MECHANICAL-PROPERTIES; MICROSTRUCTURE; VELOCITY; BEHAVIOR; EFFICIENCY; ROUGHNESS;

D O I：

10.1089/3dp.2021.0260

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Low-pressure cold spray (LPCS) has broadened the application field of cold spray owing to its portability and low cost. For additive manufacturing (AM) based on LPCS (LPCSAM), it is important to investigate the effects of parameters such as temperature and pressure of the gas, stand-off distance, gun traverse speed, and the number of scanning passes of the gun on the deposition and properties. This study aims to determine the optimal kinematic spray parameters for spraying Cu+Al2O3 powder onto an aluminum substrate through LPCS, so as to prepare for the next AM work. The deposition mass, deposition rate, microhardness, and roughness under different spraying conditions were studied. The best spraying effect, with a high deposition rate and without nozzle clogging, was obtained at a nitrogen pressure of 0.9 MPa and a temperature of 400 degrees C.

引用

页码：1260 / 1271

页数：12

共 33 条

[21] Effects of substrate roughness and spray-angle on deposition behavior of cold-sprayed Inconel 718 [J].

Singh, R. ;

Rauwald, K. -H. ;

Wessel, E. ;

Mauer, G. ;

Schruefer, S. ;

Barth, A. ;

Wilson, S. ;

Vassen, R. .

SURFACE & COATINGS TECHNOLOGY, 2017, 319 :249-259

[22] Characterization and comparison of copper coatings developed by low pressure cold spraying and laser cladding techniques [J].

Singh, Surinder ;

Singh, Parminder ;

Singh, Harpreet ;

Buddu, Ramesh Kumar .

MATERIALS TODAY-PROCEEDINGS, 2019, 18 :830-840

[23] Simulation of Critical Velocity of Cold Spray Process with Different Turbulence Models [J].

Singhal, Chirag ;

Murtaza, Qasim ;

Parvej .

MATERIALS TODAY-PROCEEDINGS, 2018, 5 (09) :17371-17379

[24] Kinetic spray coatings [J].

Van Steenkiste, TH ;

Smith, JR ;

Teets, RE ;

Moleski, JJ ;

Gorkiewicz, DW ;

Tison, RP ;

Marantz, DR ;

Kowalsky, KA ;

Riggs, WL ;

Zajchowski, PH ;

Pilsner, B ;

McCune, RC ;

Barnett, KJ .

SURFACE & COATINGS TECHNOLOGY, 1999, 111 (01) :62-71

[25] Corrosion protection and electrical conductivity of copper coatings deposited by low-pressure cold spraying [J].

Winnicki, M. ;

Malachowska, A. ;

Baszczuk, A. ;

Rutkowska-Gorczyca, M. ;

Kukla, D. ;

Lachowicz, M. ;

Ambroziak, A. .

SURFACE & COATINGS TECHNOLOGY, 2017, 318 :90-98

[26] Characterization of cermet coatings deposited by low-pressure cold spraying [J].

Winnicki, M. ;

Malachowska, A. ;

Rutkowska-Gorczyca, M. ;

Sokolowski, P. ;

Ambroziak, A. ;

Pawlowski, L. .

SURFACE & COATINGS TECHNOLOGY, 2015, 268 :108-114

[27] Stable layer-building strategy to enhance cold-spray-based additive manufacturing [J].

Wu, Hongjian ;

Xie, Xinliang ;

Liu, Meimei ;

Verdy, Christophe ;

Zhang, Yicha ;

Liao, Hanlin ;

Deng, Sihao .

ADDITIVE MANUFACTURING, 2020, 35

[28] A new approach to simulate coating thickness in cold spray [J].

Wu, Hongjian ;

Xie, Xinliang ;

Liu, Meimei ;

Chen, Chaoyue ;

Liao, Hanlin ;

Zhang, Yicha ;

Deng, Sihao .

SURFACE & COATINGS TECHNOLOGY, 2020, 382

[29] Synthesis of carbon nanotube reinforced Al matrix composite coatings via cold spray deposition [J].

Xie, Xinliang ;

Tan, Zhanqiu ;

Chen, Chaoyue ;

Xie, Yingchun ;

Wu, Hongjian ;

Yan, Xingchen ;

Gao, Shuohong ;

Li, Zhiqiang ;

Ji, Gang ;

Liao, Hanlin .

SURFACE & COATINGS TECHNOLOGY, 2021, 405

[30] Additive manufacturing of WC reinforced maraging steel 300 composites by cold spraying and selective laser melting [J].

Yan, Xingchen ;

Huang, Chunjie ;

Chen, Chaoyue ;

Bolot, Rodolphe ;

Dembinski, Lucas ;

Huang, Renzhong ;

Ma, Wenyou ;

Liao, Hanlin ;

Liu, Min .

SURFACE & COATINGS TECHNOLOGY, 2019, 371 :161-171

← 1 2 3 4 →