Synthesis of Ti3SiC2 Phases and Consolidation of MAX/SiC Composites-Microstructure and Mechanical Properties

被引：6

作者：

Wozniak, Jaroslaw ^{[1
]}

Petrus, Mateusz ^{[1
]}

Cygan, Tomasz ^{[1
]}

Adamczyk-Cieslak, Boguslawa ^{[1
]}

Moszczynska, Dorota ^{[1
]}

Olszyna, Andrzej Roman ^{[1
]}

机构：

[1] Warsaw Univ Technol, Fac Mat Sci & Engn, PL-02507 Warsaw, Poland

来源：

MATERIALS | 2023年 / 16卷 / 03期

关键词：

sintering; composites; mechanical properties; SiC; MAX phases; REACTIVE SYNTHESIS; CRACK-PROPAGATION; OXIDATION; POWDERS; BULK; SI; TI;

D O I：

10.3390/ma16030889

中图分类号：

O64 [物理化学（理论化学）、化学物理学];

学科分类号：

070304 ; 081704 ;

摘要：

The article describes the Ti3SiC2 powder synthesis process. The influence of the molar ratio and two forms of carbon on the phase composition of the obtained powders was investigated. The synthesis was carried out using a spark plasma sintering (SPS) furnace. In addition, using the obtained powders, composites reinforced with SiC particles were produced. The obtained results showed no effect of the carbon form and a significant impact of annealing on the purity of the powders after synthesis. The composites were also consolidated using an SPS furnace at two temperatures of 1300 and 1400 degrees C. The tests showed low density and hardness for sinters from 1300 degrees C (maximum 3.97 g/cm(3) and 447 HV5, respectively, for composite reinforced with 10% SiC). These parameters significantly increase for composites sintered at 1400 degrees C (maximum density 4.43 g/cm(3) and hardness 1153 HV5, for Ti3AlC2-10% SiC). In addition, the crack propagation analysis showed mechanisms typical for granular materials and laminates.

引用

页数：13

共 30 条

[1]

[Anonymous], 2006, ENCY MAT SCI TECHNOL, DOI DOI 10.1146/ANNUREV-MATSCI-062910-100448

[2] Long time oxidation study of Ti3SiC2,Ti3SiC2/SiC, and Ti3SiC2/TiC composites in air [J].

Barsoum, MW ;

Ho-Duc, LH ;

Radovic, M ;

El-Raghy, T .

JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 2003, 150 (04) :B166-B175

[3] The MN+1AXN phases:: A new class of solids;: Thermodynamically stable nanolaminates [J].

Barsoum, MW .

PROGRESS IN SOLID STATE CHEMISTRY, 2000, 28 (1-4) :201-281

[4] Layered machinable ceramics for high temperature applications [J].

Barsoum, MW ;

Brodkin, D ;

ElRaghy, T .

SCRIPTA MATERIALIA, 1997, 36 (05) :535-541

[5] A Mode I cohesive law characterization procedure for through-the-thickness crack propagation in composite laminates [J].

Bergan, Andrew ;

Davila, Carlos ;

Leone, Frank ;

Awerbuch, Jonathan ;

Tan, Tein-Min .

COMPOSITES PART B-ENGINEERING, 2016, 94 :338-349

[6] Synthesis of Ti3SiC2 powders:: Reaction mechanism [J].

Cordoba, Jose M. ;

Sayagues, Maria J. ;

Alcala, Maria D. ;

Gotor, Francisco J. .

JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2007, 90 (03) :825-830

[7] Microstructure and Mechanical Properties of Alumina Composites with Addition of Structurally Modified 2D Ti3C2 (MXene) Phase [J].

Cygan, Tomasz ;

Wozniak, Jaroslaw ;

Petrus, Mateusz ;

Lachowski, Artur ;

Pawlak, Wojciech ;

Adamczyk-Cieslak, Boguslawa ;

Jastrzebska, Agnieszka ;

Rozmyslowska-Wojciechowska, Anita ;

Wojciechowski, Tomasz ;

Ziemkowska, Wanda ;

Olszyna, Andrzej .

MATERIALS, 2021, 14 (04) :1-18

[8] Short SiC fiber/Ti3SiC2MAX phase composites: Fabrication and creep evaluation [J].

Dash, Apurv ;

Malzbender, Juergen ;

Vassen, Robert ;

Guillon, Olivier ;

Gonzalez-Julian, Jesus .

JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2020, 103 (12) :7072-7081

[9] Optimization of the Ti3SiC2 MAX phase synthesis [J].

El Saeed, M. A. ;

Deorsola, F. A. ;

Rashad, R. M. .

INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2012, 35 :127-131

[10] Ti2AlC coatings deposited by High Velocity Oxy-Fuel spraying [J].

Frodelius, Jenny ;

Sonestedt, Marie ;

Bjorklund, Stefan ;

Palmquist, Jens-Petter ;

Stiller, Krystyna ;

Hogberg, Hans ;

Hultman, Lars .

SURFACE & COATINGS TECHNOLOGY, 2008, 202 (24) :5976-5981

← 1 2 3 →