Mechanical and morphological characterizations of epoxy composites reinforced with surface modified woven cotton structures using vacuum bagging technique

被引:7
|
作者
Owen, Macaulay M. [1 ]
Achukwu, Emmanuel O. [2 ]
Rahman, Aslina Anjang Ab [3 ]
Romli, Ahmad Zafir [4 ,5 ]
Ahmad, Mohd Rozi [6 ]
Bin Shuib, Solehuddin [1 ]
Md Akil, Hazizan [7 ]
机构
[1] Univ Teknol MARA, Coll Engn, Sch Mech Engn, Biomech & Clin Engn BIOMEC Res Grp, Engn Campus, Shah Alam, Selangor, Malaysia
[2] Ahmadu Bello Univ, Dept Polymer & Text Engn, Zaria, Nigeria
[3] Univ Sains Malaysia, Sch Aerosp Engn, Engn Campus, Nibong Tebal, Malaysia
[4] Univ Teknol MARA, Inst Sci IOS, Ctr Chem Synth & Polymer Composites Res & Technol, Shah Alam, Malaysia
[5] Univ Teknol MARA, Fac Appl Sci, Shah Alam, Malaysia
[6] Univ Teknol MARA, Fac Appl Sci, Text Res Grp, Shah Alam, Malaysia
[7] Univ Sains Malaysia, Sch Mat & Mineral Resources Engn, Engn Campus, Nibong Tebal, Malaysia
关键词
Fabric-reinforced composites; weave structures; epoxy resin; surface treatment; mechanical properties; MANUFACTURING TECHNIQUES; POLYESTER; FIBERS; BEHAVIOR;
D O I
10.1080/00405000.2023.2258047
中图分类号
TB3 [工程材料学]; TS1 [纺织工业、染整工业];
学科分类号
0805 ; 080502 ; 0821 ;
摘要
Woven fabric structures facilitate the mechanical interlacement of textile yarns for increased strength, which leads to more balanced mechanical properties in a composite. This study worked on epoxy matrix composites reinforced with surface-modified cotton fabrics of different woven structures. The composites were fabricated using the resin vacuum bagging technique and mechanically characterized for tensile, three-point bending, and impact properties. Surface modification was conducted by alkali treatment using a 6% concentration of sodium hydroxide (NaOH). The interfacial adhesion of the various fabric structures and epoxy matrix was examined using a scanning electron microscope (SEM). The results obtained show that surface-treated composites yielded improved mechanical properties than untreated composites, with improvements of up to 14.4%, 36.2%, and 26.7% for impact, flexural, and tensile strengths, respectively. The different woven structures also significantly affected the mechanical performance of the composite. The composites of plain, herringbone, and twill woven structures presented better mechanical properties compared to the other woven composite structures in that order. The plain-woven composite structure, respectively, had the maximum impact, flexural, and tensile strengths of 80.03 KJ/mm2, 38.6 MPa, and 43.7 MPa. This was closely followed by the herringbone and twill-woven composite structures. SEM results revealed complete impregnation of fibers and a strong interfacial relationship between the thermoset matrix and the treated cotton fabrics in the composite laminate structures produced via the vacuum bagging technique. In conclusion, the study indicated that different weave structures and fiber surface treatments, as well as the vacuum bagging technique used, are of significant importance in enhancing the overall mechanical performance of woven fabric composites.
引用
收藏
页码:1606 / 1620
页数:15
相关论文
共 29 条
  • [21] Mechanical Properties of Epoxy Composites Reinforced Using a Carbon Fiber Film Type Coated with Carboxyl Graphene via an Economical Electrophoretic Deposition Technique
    Jatothu, Praveenkumar
    Srivastava, Alok K.
    Singh, Aparna
    ACS APPLIED ENGINEERING MATERIALS, 2023, 1 (10): : 2734 - 2744
  • [22] LDPE-based composites reinforced with surface modified cellulose fibres: 3D morphological and morphometrical analyses to understand the improved mechanical performance
    Ferreia, F. V.
    Trindade, G. N.
    Lona, L. M. F.
    Bernardes, J. S.
    Gouveia, R. F.
    EUROPEAN POLYMER JOURNAL, 2019, 117 : 105 - 113
  • [23] Effect of surface treatment and fiber loading on the physical, mechanical, sliding wear, and morphological characteristics of tasar silk fiber waste-epoxy composites for multifaceted biomedical and engineering applications: fabrication and characterizations
    Ranakoti, Lalit
    Gangil, Brijesh
    Rajesh, Pawan Kumar
    Singh, Tej
    Sharma, Shubham
    Li, Changhe
    Ilyas, R. A.
    Mahmoud, Omar
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2022, 19 : 2863 - 2876
  • [24] Evaluation of Mechanical, Wear and Fracture Behavior of Silicon Carbide Particulates Reinforced Al7075 Composites using Response Surface Methodology Technique
    Ravikumar, M.
    Naik, Rudra
    Rammohan, Y. S.
    Raghavendra, S.
    Suresh, R.
    JOURNAL OF MATERIALS AND ENGINEERING STRUCTURES, 2023, 10 (03): : 601 - 613
  • [25] Effects of surface-modified silica nanoparticles attached graphene oxide using isocyanate-terminated flexible polymer chains on the mechanical properties of epoxy composites
    Jiang, Tongwu
    Kuila, Tapas
    Kim, Nam Hoon
    Lee, Joong Hee
    JOURNAL OF MATERIALS CHEMISTRY A, 2014, 2 (27) : 10557 - 10567
  • [26] Fatigue, fracture toughness and dynamic mechanical behaviour of CTBN rubber toughened silane surface-modified pineapple fiber and micro B4C-reinforced epoxy hybrid composites
    Jaiganesh, V.
    Vinothkumar, M.
    Gurusamy, P.
    BIOMASS CONVERSION AND BIOREFINERY, 2024, 14 (08) : 9739 - 9748
  • [27] Fatigue, fracture toughness and dynamic mechanical behaviour of CTBN rubber toughened silane surface-modified pineapple fiber and micro B4C-reinforced epoxy hybrid composites
    V. Jaiganesh
    M. Vinothkumar
    Gurusamy P.
    Biomass Conversion and Biorefinery, 2024, 14 : 9739 - 9748
  • [28] Improvements of adhesion strength of water-based epoxy resin on carbon fiber reinforced polymer (CFRP) composites via building surface roughness using modified silica particles
    Li, Meiqi
    Zhang, Ling
    Li, Xiaofei
    Wang, Ruitao
    Wu, Xiaofeng
    Zhang, Donghai
    Chen, Yunfa
    COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2023, 169
  • [29] Effects of surface-modified pineapple fibre-reinforced micro B4C and CTBN rubber particle toughened epoxy hybrid composites in mechanical, impact damage, thermal and water absorption behavior
    Vinothkumar, M.
    Jaiganesh, V
    Malarvannan, R. Raviraja
    MATERIALS RESEARCH EXPRESS, 2019, 6 (11)