The anisotropic wear and friction property of Inconel 718 superalloy fabricated by laser directed energy deposition

被引：19
|
作者：
Liu, Fencheng [1 ]
Gao, Jian [1 ]
Liu, Fenggang [1 ]
Xu, Yang [1 ]
You, Qifan [1 ]
Huang, Chunping [1 ]
Hu, Xiaoan [2 ]
Zheng, Haizhong [1 ]
Lin, Xin [3 ]
机构：
[1] Nanchang Hangkong Univ, Natl Def Key Discipline Lab Light Alloy Proc Sci &, Nanchang 330063, Peoples R China
[2] Nanchang Hangkong Univ, Sch Aerocraft Engn, Nanchang 330063, Peoples R China
[3] Northwestern Polytech Univ, Stake Key Lab Solidificat Proc, Xian 710072, Peoples R China
来源：
TRIBOLOGY INTERNATIONAL | 2023年 / 188卷
基金：
中国国家自然科学基金;
关键词：
Laser directed energy deposition; Ni-based superalloy; Anisotropy; Wear property; FATIGUE-CRACK GROWTH; MECHANICAL-PROPERTIES; HEAT-TREATMENT; TAILORED MICROSTRUCTURE; CORROSION; NANOCOMPOSITES; TEMPERATURE; RESISTANCE; INTERFACE; BEHAVIOR;
D O I：
10.1016/j.triboint.2023.108835
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The effect of crystal orientation and heat treatment on microstructure and wear properties of Inconel 718 superalloy fabricated by laser directed energy deposition (LDED) were analyzed and compared with forged samples. Fully heat treated samples presented the lowest wear rate and better resistance to friction compared with other condition samples. The direct aging treated samples also had better wear resistance attributed to its microhardness and microstructure and were mainly abrasive wear with a large amount of wear debris and deeper scratches on the worn surface. As for the anisotropy of microstructure in LDED samples, the wear properties in different crystal orientations were different, and better wear performance was obtained in the section which is vertical to the deposition direction.
引用
收藏
页数：14
相关论文
共 50 条
  • [31] Effect of process parameters on mechanical properties of Inconel718 superalloy fabricated by directional energy deposition
    Tianhao Jia
    Bin Zou
    Wenbo Liu
    Ting Lei
    Hongjian Ding
    The International Journal of Advanced Manufacturing Technology, 2023, 128 : 2863 - 2883
  • [32] Effect of process parameters on mechanical properties of Inconel718 superalloy fabricated by directional energy deposition
    Jia, Tianhao
    Zou, Bin
    Liu, Wenbo
    Lei, Ting
    Ding, Hongjian
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2023, 128 (7-8): : 2863 - 2883
  • [33] Laves phase tuning for enhancing high temperature mechanical property improvement in laser directed energy deposited Inconel 718
    Sui, Shang
    Li, Zuo
    Zhong, Chongliang
    Zhang, Qiang
    Gasser, Andres
    Chen, Jing
    Chew, Youxiang
    Bi, Guijun
    COMPOSITES PART B-ENGINEERING, 2021, 215
  • [34] Plastic deformation behavior and dynamic recrystallization of Inconel 625 superalloy fabricated by directed energy deposition
    Hu, Y. L.
    Lin, X.
    Li, Y. L.
    Zhang, S. Y.
    Gao, X. H.
    Liu, F. G.
    Li, X.
    Huang, W. D.
    MATERIALS & DESIGN, 2020, 186
  • [35] Influence of post-heat-treatment on the microstructure and fracture toughness properties of Inconel 718 fabricated with laser directed energy deposition additive manufacturing
    Yu, Xiaobin
    Lin, Xin
    Liu, Fencheng
    Wang, Lilin
    Tang, Yao
    Li, Jiacong
    Zhang, Shuya
    Huang, Weidong
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 798
  • [36] Wear Behavior of Laser Surface Melted Inconel 718
    Sharma, S. K.
    Biswas, K.
    Nath, A. K.
    Manna, I
    Majumdar, J. Dutta
    LASERS IN ENGINEERING, 2021, 50 (1-3) : 1 - 13
  • [37] The formation and dissolution mechanisms of Laves phase in Inconel 718 fabricated by selective laser melting compared to directed energy deposition and cast
    Zhang, Shuya
    Wang, Lilin
    Lin, Xin
    Yang, Haiou
    Huang, Weidong
    COMPOSITES PART B-ENGINEERING, 2022, 239
  • [38] Influence of grain inhomogeneity and precipitates on the stress rupture properties of Inconel 718 superalloy fabricated by selective laser melting
    Zhang, Shuya
    Lin, Xin
    Wang, Lilin
    Yu, Xiaobin
    Yang, Haiou
    Lei, Liming
    Huang, Weidong
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 803
  • [39] Improved plasticity of Inconel 718 superalloy fabricated by selective laser melting through a novel heat treatment process
    Li, X.
    Shi, J. J.
    Cao, G. H.
    Russell, A. M.
    Zhou, Z. J.
    Li, C. P.
    Chen, G. F.
    MATERIALS & DESIGN, 2019, 180
  • [40] Microstructural evolution and high-temperature oxidation behavior of oxide dispersion strengthened Inconel 625 superalloy fabricated by directed energy deposition
    Zou, Xiaodong
    Yang, Ke
    Li, Jingkui
    Xie, Xu
    Pan, Linlin
    MATERIALS CHARACTERIZATION, 2024, 210
12345