Microstructure evolution and fracture behavior of Ti-6Al-4V fabricated by WAAM-LDM additive manufacturing

被引：32

作者：

Zhou, Siyu ^{[1
]}

Zhang, Jianfei ^{[1
]}

Yang, Guang ^{[1
]}

Wang, Yushi ^{[1
]}

Li, Bobo ^{[1
]}

An, Da ^{[1
]}

Zheng, Jianshen ^{[1
]}

Wei, Wenyi ^{[2
]}

机构：

[1] Shenyang Aerosp Univ, Sch Mechatron Engn, Shenyang 110136, Peoples R China

[2] Liaoning Equipment Mfg Vocat & Tech Coll, Shenyang 110164, Peoples R China

来源：

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T | 2024年 / 28卷

关键词：

Additive manufacturing; Wire arc additive manufacturing; Laser deposition manufacturing; Ti-6Al-4V; Microstructure; Fracture behavior; MECHANICAL-PROPERTIES; LASER DEPOSITION; TI-6A1-4V ALLOY; PART I; WIRE; DEFECTS;

D O I：

10.1016/j.jmrt.2023.11.255

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

WAAM and LDM are two typical DED technologies. WAAM-LDM additive manufacturing technology can achieve the purpose of producing large and complex Ti-6Al-4V components, improving processing efficiency and precision. However, there is a lack of in-depth research on the microstructure evolution mechanism and the fracture behavior of WAAM-LDM samples. Therefore, horizontal and vertical WAAM samples were invoked as the substrate for LDM processes in this study, and the mechanical properties and tensile fracture behavior under different load directions were evaluated. The results show that the samples fabricated by WAAM-LDM manufacturing consist of four zones: WAAM zone, heat affected zone (HAZ), remelting zone (RZ) and LDM zone. WAAM zone mainly composed of coarse colony structure, HAZ and RZ are dominated by alpha colonies and fine basketweave structure, respectively, and LDM zone consists of acicular alpha phases and fine basketweave structure. The thickness of alpha laths shows a trend of 'WAAM > HAZ > LDM > RZ'. The strengths are greatly improved at the interfaces due to the good metallurgical bonding and finer microstructure. All the fractures locate at WAAM zone during tensile test and propagate along the basketweave structure. These strengths of WAAM-LDM samples under the action of horizontal loading are higher than that of WAAM samples, and all the elongations of WAAM-LDM samples are higher than 10 %.

引用

页码：347 / 362

页数：16

共 42 条

[1] Influence of microstructure on mechanical properties of laser metal wire-deposited Ti-6Al-4V [J].

Akerfeldt, Pia ;

Antti, Marta-Lena ;

Pederson, Robert .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 674 :428-437

[2] Hybrid manufacturing of components from Ti-6Al-4V by metal forming and wire-arc additive manufacturing [J].

Bambach, M. ;

Sizova, I ;

Sydow, B. ;

Hemes, S. ;

Meiners, F. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2020, 282

[3] Wire based additive layer manufacturing: Comparison of microstructure and mechanical properties of Ti-6Al-4V components fabricated by laser-beam deposition and shaped metal deposition [J].

Baufeld, Bernd ;

Brandl, Erhard ;

van der Biest, Omer .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2011, 211 (06) :1146-1158

[4] Anisotropic tensile behavior of Ti-6Al-4V components fabricated with directed energy deposition additive manufacturing [J].

Carroll, Beth E. ;

Palmer, Todd A. ;

Beese, Allison M. .

ACTA MATERIALIA, 2015, 87 :309-320

[5] Study on appearance and mechanical behavior of additively manufacturing of Ti-6Al-4V alloy by using cold metal transfer [J].

Chen, Chao ;

Chen, Furong ;

Yang, Yihang ;

Zhang, Huijing .

CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2021, 35 :250-258

[6] Deciphering the transformation pathway in laser powder-bed fusion additive manufacturing of Ti-6Al-4V alloy [J].

Chen, J. ;

Fabijanic, D. ;

Zhang, T. ;

Lui, E. W. ;

Brandt, M. ;

Xu, W. .

ADDITIVE MANUFACTURING, 2022, 58

[7] Coaxial laser metal wire deposition of Ti6Al4V alloy: process, microstructure and mechanical properties [J].

Chen, Yuan ;

Chen, Xi ;

Jiang, Meng ;

Lei, Zhenglong ;

Wang, Zhe ;

Liang, Jingwei ;

Wu, Shibo ;

Ma, Shengchong ;

Jiang, Nan ;

Chen, Yanbin .

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2022, 20 :2578-2590

[8] Microstructure and mechanical properties of as-built and heat-treated Ti-6Al-4V alloy prepared by cold metal transfer additive manufacturing [J].

Gou, Jian ;

Shen, Junqi ;

Hu, Shengsun ;

Tian, Yinbao ;

Liang, Ying .

JOURNAL OF MANUFACTURING PROCESSES, 2019, 42 :41-50

[9] The role of lattice defects, element partitioning and intrinsic heat effects on the microstructure in selective laser melted Ti-6Al-4V [J].

Haubrich, Jan ;

Gussone, Joachim ;

Barriobero-Vila, Pere ;

Kurnsteiner, Philipp ;

Jaegle, Eric A. ;

Raabe, Dierk ;

Schell, Norbert ;

Requena, Guillermo .

ACTA MATERIALIA, 2019, 167 :136-148

[10] A Study On The Mechanical Properties Of Hybrid Parts Manufactured By Forging And Wire Arc Additive Manufacturing [J].

Hirtler, Markus ;

Jedynak, Angelika ;

Sydow, Benjamin ;

Sviridov, Alexander ;

Bambach, Markus .

23RD INTERNATIONAL CONFERENCE ON MATERIAL FORMING, 2020, 47 :1141-1148

← 1 2 3 4 5 →