Effect of laser cladding parameters on Inconel 718 coating performance and multi-parameter optimization

被引：49

作者：

Xu, Zhenyang ^{[1
]}

Yuan, Junfeng ^{[1
,2
,3
]}

Wu, Mingyu ^{[2
]}

Arif, Abul Fazal M. ^{[3
]}

Li, Dongyang ^{[2
]}

机构：

[1] China Univ Min & Technol, Sch Mechatron Engn, Xuzhou 221116, Peoples R China

[2] Univ Alberta, Chem & Mat Engn Dept, Edmonton, AB T6G 2H5, Canada

[3] McMaster Univ, McMaster Mfg Res Inst MMRI, Dept Mech Engn, 1280 Main St West, Hamilton, ON L82 4L7, Canada

来源：

OPTICS AND LASER TECHNOLOGY | 2023年 / 158卷

基金：

中国博士后科学基金;

关键词：

Laser cladding; Coating properties; Multi; -response; Parameter optimization; Taguchi method; Grey relational analysis; MECHANICAL-PROPERTIES; RELATIONAL ANALYSIS; STAINLESS-STEEL; CORROSION; MICROSTRUCTURE; ALLOY; WEAR;

D O I：

10.1016/j.optlastec.2022.108850

中图分类号：

O43 [光学];

学科分类号：

070207 ; 0803 ;

摘要：

The purpose of this study is to improve the quality of the multi-track laser cladding coating. The Taguchi-Grey relation method was selected to realize process parameter optimization. The Taguchi method is used to design an L16 orthogonal experiment. The influence of three important laser cladding parameters (laser power, powder feeding rate, and scanning speed) on the micro-hardness, maximum load value, yield strength, UTS, and elon-gation had been analyzed based on the analysis of variance (ANOVA) and signal to noise ratio (SNR) methods. The results showed that the yield strength, UTS, and elongation were significantly affected by the laser power; the powder feeding rate denoted a highly significant influence on the microhardness and yield strength; and the scanning speed was a highly significant factor that had an influence on the maximum load value. Then, grey relational analysis (GRA) was used to convert five response targets into a single grey relational grade (GRG) that could be quantified in order to optimize the parameters for maximum micro-hardness, maximum load value, yield strength, UTS, and elongation. Finally, the optimum cladding process parameters were obtained. Through analysis of microstructure, the reduction of the Laves phase might be the main reason for the improvement of coating performance after optimization.

引用

页数：15

共 42 条

[1] Investigation of powder fed laser cladding of NiCr-chromium carbides single-tracks on titanium aluminide substrate [J].

Aghili, S. E. ;

Shamanian, M. .

OPTICS AND LASER TECHNOLOGY, 2019, 119

[2] Prediction of solidification cracking by an empirical-statistical analysis for laser cladding of Inconel 718 powder on a non-weldable substrate [J].

Alizadeh-Sh, M. ;

Marashi, S. P. H. ;

Ranjbarnodeh, E. ;

Shoja-Razavi, R. ;

Oliveira, J. P. .

OPTICS AND LASER TECHNOLOGY, 2020, 128

[3] Multi-objective Optimization of Woven Fabric Parameters Using Taguchi-Grey Relational Analysis [J].

Almetwally, Alsaid Ahemd .

JOURNAL OF NATURAL FIBERS, 2020, 17 (10) :1468-1478

[4] Development of highly hard and corrosion resistant A286 stainless steel through plasma nitrocarburizing process [J].

Alphonsa, J. ;

Raja, V. S. ;

Mukherjee, S. .

SURFACE & COATINGS TECHNOLOGY, 2015, 280 :268-276

[5] Microstructure and Abrasive Wear Performance of Ni-Wc Composite Microwave Clad [J].

Bansal, Amit ;

Zafar, Sunny ;

Sharma, Apurbba Kumar .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2015, 24 (10) :3708-3716

[6]

Brandt M., 2009, International Heat Treatment and Surface Engineering, V3, P105, DOI 10.1179/174951409X12542264513843

[7] Laser cladding of nanoparticle TiC ceramic powder: Effects of process parameters on the quality characteristics of the coatings and its prediction model [J].

Chen, Tao ;

Wu, Weining ;

Li, Wenpeng ;

Liu, Defu .

OPTICS AND LASER TECHNOLOGY, 2019, 116 :345-355

[8] Laser cladding: an experimental study of geometric form and hardness of coating using statistical analysis [J].

Davim, J. Paulo ;

Oliveira, C. ;

Cardoso, A. .

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2006, 220 (09) :1549-1554

[9] Potentiodynamic study of the influence of gamma prime and eta phases on pitting corrosion of A286 superalloy [J].

De Tiedra, Pilar ;

Martin, Oscar ;

San-Juan, Manuel .

JOURNAL OF ALLOYS AND COMPOUNDS, 2016, 673 :231-236

[10] Multi-response optimization of laser cladding for TiC particle reinforced Fe matrix composite based on Taguchi method and grey relational analysis [J].

Deng, Dewei ;

Li, Tianshu ;

Huang, Zhiye ;

Jiang, Hao ;

Yang, Shuhua ;

Zhang, Yong .

OPTICS AND LASER TECHNOLOGY, 2022, 153

← 1 2 3 4 5 →