Fatigue and Fracture Behavior of AlSi10Mg Manufactured by Selective Laser Melting: A Review

被引：16

作者：

Jiang, Z. ^{[1
]}

Sun, J. ^{[2
]}

Berto, F. ^{[3
,4
]}

Wang, X. ^{[1
]}

Qian, G. ^{[2
]}

机构：

[1] Beijing Jiaotong Univ, Sch Mech Elect & Control Engn, Beijing 100044, Peoples R China

[2] Chinese Acad Sci, Inst Mech, State Key Lab Nonlinear Mech, Beijing 100190, Peoples R China

[3] Norwegian Univ Sci & Technol, Dept Mech & Ind Engn, N-7491 Trondheim, Norway

[4] Sapienza Univ Rome, Dept Chem Engn Mat Environm, I-00184 Rome, Italy

来源：

PHYSICAL MESOMECHANICS | 2023年 / 26卷 / 04期

基金：

中国国家自然科学基金;

关键词：

selective laser melting; AlSi10Mg; crack initiation; post-treatment; fatigue life prediction; HIGH-CYCLE FATIGUE; POWDER BED FUSION; SURFACE-ROUGHNESS; RESIDUAL-STRESSES; MELTED ALSI10MG; CRACK INITIATION; LIFE PREDICTION; PROCESS PARAMETERS; BUILD ORIENTATION; ALLOY INFLUENCE;

D O I：

10.1134/S102995992304001X

中图分类号：

O3 [力学];

学科分类号：

08 ; 0801 ;

摘要：

Selective laser melting (SLM) is one of the most promising metal additive manufacturing technologies. SLMed Al-Si alloys have been widely used in the rail transport, aerospace, and automotive industries. Recently, the fatigue and fracture properties of SLMed Al-Si alloys have attracted considerable attention due to their application in critical load-bearing structures. This review aims to better understand the recent progress on the fatigue and fracture investigations of SLMed Al-Si alloys, especially AlSi10Mg, with emphasis on the effect of defects, heterogeneous microstructure, residual stress, and post-treatment methods. In addition, fatigue and fracture modeling methods are discussed. Finally, the challenges and future research opportunities are prospected.

引用

页码：367 / 390

页数：24

共 117 条

[1] 3D printing of Aluminium alloys: Additive Manufacturing of Aluminium alloys using selective laser melting [J].

Aboulkhair, Nesma T. ;

Simonelli, Marco ;

Parry, Luke ;

Ashcroft, Ian ;

Tuck, Christopher ;

Hague, Richard .

PROGRESS IN MATERIALS SCIENCE, 2019, 106

[2] Improving the fatigue behaviour of a selectively laser melted aluminium alloy: Influence of heat treatment and surface quality [J].

Aboulkhair, Nesma T. ;

Maskery, Ian ;

Tuck, Chris ;

Ashcroft, Ian ;

Everitt, Nicola M. .

MATERIALS & DESIGN, 2016, 104 :174-182

[3]

Aboulkhair NT., 2014, Addit Manuf, V1, P77, DOI DOI 10.1016/J.ADDMA.2014.08.001

[4] Effects of build orientation and heat treatments on the tensile and fracture toughness properties of additively manufactured AlSi10Mg [J].

Araujo, Luana C. ;

Gabriel, Andre H. G. ;

da Fonseca, Eduardo B. ;

Avila, Julian A. ;

Jardini, Andre L. ;

Seno Junior, Roberto ;

Lopes, Eder S. N. .

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2022, 213

[5] Effects of post-processing route on fatigue performance of laser powder bed fusion Inconel 718 [J].

Ardi, Dennise Tanoko ;

Guowei, Lim ;

Maharjan, Niroj ;

Mutiargo, Bisma ;

Leng, Seng Hwee ;

Srinivasan, Raghavan .

ADDITIVE MANUFACTURING, 2020, 36

[6] Investigation on fatigue strength of sand-blasted DMLS-AlSi 10Mg alloy [J].

Avanzini, Andrea ;

Battini, Davide ;

Gelfi, Marcello ;

Girelli, Luca ;

Petrogalli, Candida ;

Pola, Annalisa ;

Tocci, Marialaura .

25TH INTERNATIONAL CONFERENCE ON FRACTURE AND STRUCTURAL INTEGRITY, 2019, 18 :119-128

[7] Very high-cycle fatigue properties and microstructural damage mechanisms of selective laser melted AlSi10Mg alloy [J].

Awd, Mustafa ;

Siddique, Shafaqat ;

Johannsen, Jan ;

Emmelmann, Claus ;

Walther, Frank .

INTERNATIONAL JOURNAL OF FATIGUE, 2019, 124 :55-69

[8] Influence of heat treatment on the high-cycle fatigue properties and fatigue damage mechanism of selective laser melted AlSi10Mg alloy [J].

Baek, Min-Seok ;

Kreethi, R. ;

Park, Tae-Hyun ;

Sohn, Yongho ;

Lee, Kee-Ahn .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 819

[9] Application of mechanical surface finishing processes for roughness reduction and fatigue improvement of additively manufactured Ti-6Al-4V parts [J].

Bagehorn, S. ;

Wehr, J. ;

Maier, H. J. .

INTERNATIONAL JOURNAL OF FATIGUE, 2017, 102 :135-142

[10] On the fatigue strength enhancement of additive manufactured AlSi10Mg parts by mechanical and thermal post-processing [J].

Bagherifard, Sara ;

Beretta, Niccolo ;

Monti, Stefano ;

Riccio, Martina ;

Bandini, Michele ;

Guagliano, Mario .

MATERIALS & DESIGN, 2018, 145 :28-41

← 1 2 3 4 5 6 7 8 9 10 →