Influence of Different Contact Conditions on Friction Properties of AISI 430 Steel Sheet with Deep Drawing Quality

被引:8
|
作者
Luiz, Valmir Dias [1 ,2 ]
Junior dos Santos, Anderson [2 ]
Camara, Marcelo Araujo [2 ]
de Matos Rodrigues, Paulo Cesar [2 ]
机构
[1] Univ Fed Minas Gerais, Grad Program Mech Engn, Ave Antonio Carlos, 6627, BR-31270901 Belo Horizonte, MG, Brazil
[2] Ctr Fed Educ Tecnol Minas Gerais, Dept Met & Chem, R 19 Novembro 121 Ctr Norte, BR-35180008 Timoteo, MG, Brazil
关键词
friction conditions; pin-on-disk test; bending under tension test; strip-tension test; AISI; 430; coefficient of friction; FERRITIC STAINLESS-STEEL; DELAMINATION; BEHAVIOR;
D O I
10.3390/coatings13040771
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
This article aims to investigate the influence of different contact conditions on the friction properties of an Nb-stabilized AISI 430 ferritic stainless-steel sheet with deep drawing quality. Three tribological tests were performed: pin-on-disk, bending under tension, and strip-tension test. Moreover, counter samples of a hard metal (WC-12%Co) with surface finishes of 0.27 and 0.54 mu m were used in the friction tests under dry and lubricated conditions. The influence of the texture and relative elongation of the strip on formability also were investigated. A comparative analysis of the results revealed that the coefficients of friction, wear, lubricant efficiency, and hardness measured below the wear surface indicated a strong dependence on surface roughness and the friction test type. The coefficients of friction obtained from the pin-on-disk test were higher than those obtained from the formability tests. In addition, the coefficient of friction increased with increasing relative elongation during the formability tests; it was higher in the bending-under-tension test than in the strip-tension test, mainly owing to the increasing strip surface roughness. The contact pressure during the formability tests was non-uniform during strip sliding under the tool. According to our results, for each friction condition in a specific area of the forming die, there is a value of the coefficient of friction, depending on the kinematic conditions. Therefore, the results can be used as input data to define design guidelines, improve productivity, and improve product quality from this steel sheet.
引用
收藏
页数:20
相关论文
共 50 条
  • [1] On the influence of deformation of deep drawing quality steel sheet on surface topography and friction
    Trzepiecinski, Tomasz
    Fejkiel, Romuald
    TRIBOLOGY INTERNATIONAL, 2017, 115 : 78 - 88
  • [2] THE INFLUENCE OF THE DEFORMATIONAL AGING AND THE CONDITIONS OF STRESS ON THE PROPERTIES OF THE DEEP-DRAWING STEEL SHEET
    HRIVNAK, A
    SOBOTOVA, L
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1992, 34 (1-4) : 425 - 430
  • [3] Influence of drawing speed and anisotropy on the tribological behavior and fracture of an AISI 430Nb sheet steel
    Luiz, Valmir Dias
    Amaral, Erriston Campos
    de Souza, Vitor Pagani
    de Matos Rodrigues, Paulo Cesar
    MATERIA-RIO DE JANEIRO, 2022, 27 (01):
  • [4] Influence of drawing speed on friction conditions in deep drawing
    Vpliv hitrosti vlecenja na torne razmere pri globokem vleku
    Gologranc, Franc, 1600, (35): : 4 - 6
  • [5] DEEP DRAWING STEEL SHEET SURFACE QUALITY
    WALTER, RJ
    JOURNAL OF METALS, 1953, 5 (05): : 630 - 631
  • [6] Influence of CSP coiling temperature on microstructure and properties of deep drawing steel sheet
    Wu, Lei
    Liu, Ya-Zheng
    Cheng, Xiao-Jie
    Sun, You-Bo
    Tian, Rong-Bin
    Dong, Rui-Feng
    Zhang, Xiao-Yan
    Cailiao Rechuli Xuebao/Transactions of Materials and Heat Treatment, 2010, 31 (04): : 81 - 85
  • [7] Failure analysis of AISI 430 stainless steel sheet under stretching and bending conditions
    Luiz, Valmir Dias
    de Matos Rodrigues, Paulo Cesar
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2022, 121 (3-4): : 2759 - 2772
  • [8] Failure analysis of AISI 430 stainless steel sheet under stretching and bending conditions
    Valmir Dias Luiz
    Paulo César de Matos Rodrigues
    The International Journal of Advanced Manufacturing Technology, 2022, 121 : 2759 - 2772
  • [9] Behavior of AISI 430 ferritic steel in relation to AISI 304 austenitic steel subjected to different lubrication conditions
    Faria, Gessica Seara
    Labiapari, Wilian da Silva
    Brandao, Luiz Paulo
    MATERIA-RIO DE JANEIRO, 2024, 29 (03):
  • [10] INFLUENCE OF DEEP-DRAWING CONDITIONS ON EARING OF ALUMINIUM SHEET
    WRIGHT, JC
    JOURNAL OF THE INSTITUTE OF METALS, 1965, 93 : 289 - &