Influences of WEDM constraints on tribological and micro structural depictions of SiC-Gr strengthened Al2219 composites

被引：6

作者：

Babu, R. Dilli ^{[1
,5
]}

Gurusamy, P. ^{[2
]}

Bejaxhin, A. Bovas Herbert ^{[3
]}

Chandramohan, P. ^{[4
]}

机构：

[1] Misrimal Navajee Munoth Jain Engn Coll, Dept Mech Engn, Chennai 600097, India

[2] Chennai Inst Technol, Ctr Addit Mfg, Chennai 600069, India

[3] SIMATS, Saveetha Sch Engn, Dept Mech Engn, Chennai, India

[4] Rajalakshmi Engn Coll, Dept Mechatron Engn, Chennai, India

[5] Anna Univ, Fac Mech Engn, Chennai 600025, India

来源：

TRIBOLOGY INTERNATIONAL | 2023年 / 185卷

关键词：

Wire EDM; Silicon carbide; Graphite; Metal matric composite; Wear; Surface roughness; PARAMETERS;

D O I：

10.1016/j.triboint.2023.108478

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The creation of this work is made by mixing various weight percentages of SiC and consistent Graphite with liquefied Al2219. For various mechanical tests including hardness, ductility, flexural, and tensile, are conducted and tested. The broken specimens of composites discovered using a filtered electron magnifying equipment (SEM). The best mechanical properties are identified in composite materials. Additionally, a similar material is focussed on the wear test. The composite with 4% SiC and 0.5% Graphite shown improved mechanical performance among the five different groupings of sic and graphite. The optimized results and the influencing parameters of electrical release WEDM were higher Material Expulsion Rate with less discomfort on the surface and boundary for wear testing also attained with decreased wear rate.

引用

页数：10

共 14 条

[1] Multi response optimization of wire-EDM process parameters of ballistic grade aluminium alloy [J].

Bobbili, Ravindranadh ;

Madhu, V. ;

Gogia, A. K. .

ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH, 2015, 18 (04) :720-726

[2] Analysis of response variables in WEDM of Inconel 718 using Taguchi technique [J].

Dabade, U. A. ;

Karidkar, S. S. .

RESEARCH AND INNOVATION IN MANUFACTURING: KEY ENABLING TECHNOLOGIES FOR THE FACTORIES OF THE FUTURE - PROCEEDINGS OF THE 48TH CIRP CONFERENCE ON MANUFACTURING SYSTEMS, 2016, 41 :886-891

[3] Production and wear characterisation of AA 6061 matrix titanium carbide particulate reinforced composite by enhanced stir casting method [J].

Gopalakrishnan, S. ;

Murugan, N. .

COMPOSITES PART B-ENGINEERING, 2012, 43 (02) :302-308

[4] The machining characteristics of polycrystalline diamond (PCD) by micro-WEDM [J].

Hsu, F. C. ;

Tai, T. Y. ;

Vo, V. N. ;

Chen, S. Y. ;

Chen, Y. H. .

PROCEEDINGS OF THE SEVENTEENTH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM), 2013, 6 :261-266

[5]

Kenneth KanayoAlaneme, 2015, J KING SAUD U ENG SC, V2015

[6] Influence of Electro Discharge Machining of Biodegradable Magnesium on the Biocompatibility [J].

Klocke, F. ;

Schwade, M. ;

Klink, A. ;

Veselovac, D. ;

Kopp, A. .

FIRST CIRP CONFERENCE ON BIOMANUFACTURING, 2013, 5 :88-93

[7]

Kumar A., 2013, J MATER RES TECHNOL, V2, P250, DOI DOI 10.1016/J.JMRT.2013.03.015

[8]

Lakshmipathy J., 2014, Tribology in Industry, V36, P117

[9] CNT reinforced light metal composites produced by melt stirring and by high pressure die casting [J].

Li, Qianqian ;

Rottmair, Christian A. ;

Singer, Robert F. .

COMPOSITES SCIENCE AND TECHNOLOGY, 2010, 70 (16) :2242-2247

[10]

Stojanovic B, 2018, Applied Engineering Letters Journal of Engineering and Applied Sciences, V3, P52, DOI [10.18485/aeletters.2018.3.2.2, 10.18485/aeletters.2018.3.2.2, DOI 10.18485/AELETTERS.2018.3.2.2]

← 1 2 →