Synthesis and Basic Properties of Y1-xYbxVO4 Obtained by High-Energy Ball Milling and High-Temperature Treatment

被引:1
|
作者
Piz, Mateusz [1 ]
Filipek, Elzbieta [1 ]
Klukowski, Daniel [2 ]
Kochmanski, Pawel [3 ]
机构
[1] West Pomeranian Univ Technol Szczecin, Fac Chem Technol & Engn, Dept Inorgan & Analyt Chem, Al Piastow 42, PL-71065 Szczecin, Poland
[2] Maritime Univ Szczecin, Fac Nav, Dept Geoinformat, Waly Chrobrego 1-2, PL-70500 Szczecin, Poland
[3] West Pomeranian Univ Technol Szczecin, Fac Mech Engn & Mechatron, Al Piastow 19, PL-70310 Szczecin, Poland
关键词
solid solution Y1-xYbxVO4; mechanochemical synthesis; XRD; UV-VIS/DRS; semiconductors; RARE-EARTH ORTHOVANADATES; OPTICAL-PROPERTIES; CRYSTAL-STRUCTURE; THIN-FILMS; YVO4; GROWTH; NANOPARTICLES; EU3+; NANOCOMPOSITES; THERMOMETRY;
D O I
10.3390/su151914606
中图分类号
X [环境科学、安全科学];
学科分类号
08 ; 0830 ;
摘要
The main objective of this work was to experimentally confirm that a continuous, substitutional solid solution of a general formula Y1-xYbxVO4 is formed in the pseudo-binary system YVO4-YbVO4, and to investigate its basic unknown properties as a function of composition for 0.00 < x < 1.00. To date, such a solid solution has been obtained and characterized to a limited extent, but only for a few selected compositions. This solution was obtained by a high temperature and, for the first time, using mechanochemical methods. For the solution obtained by the high-energy ball-milling method, unknown physicochemical properties were established over its entire range of homogeneity. The solution was synthesized from mixtures of yttrium orthovanadate (V) with ytterbium (III) orthovanadate (V) of different compositions and investigated by XRD, IR, SEM, and UV-Vis(DRS) methods. It was found that Y1-xYbxVO4 crystallizes in a tetragonal system. The results confirmed that the solid solution Y1-xYbxVO4 has a structure of YVO4 and YbVO4, and its structure is composed of YbO6 and YO6 octahedrons and VO4 tetrahedrons. Moreover, if the parameter (x) in the solid solution Y1-xYbxVO4 increases, its crystalline lattice contracts and the value of the energy gap decreases. This solid solution is stable in the air atmosphere at least up to similar to 1500 degrees C. The estimated band gap for this solid solution indicates that it belongs to the semiconductors.
引用
收藏
页数:17
相关论文
共 50 条
  • [21] Low-Temperature Processing of PZT Thick Film by Seeding and High-Energy Ball Milling and Studies on Electrical Properties
    Soma Dutta
    A. Antony Jeyaseelan
    S. Sruthi
    Journal of Electronic Materials, 2013, 42 : 3524 - 3528
  • [22] Microwave-Assisted High-Energy Ball Milling Synthesis of SBT Nano-Ceramics
    Sahu, R.
    Swain, S.
    Mahapatra, A.
    Negi, R. R.
    Samanta, B.
    Nanda, D.
    Kumar, P.
    INTEGRATED FERROELECTRICS, 2020, 205 (01) : 177 - 185
  • [23] Dielectric properties of vanadium doped barium titanate synthesized via high-energy ball milling
    Dulian, Piotr
    Bak, Wojciech
    Wieczorek-Ciurowa, Krystyna
    Kajtoch, Czeslaw
    MATERIALS SCIENCE-POLAND, 2014, 32 (02): : 257 - 263
  • [24] Mechanical and electrical properties of Cu-Ta nanocomposites prepared by high-energy ball milling
    Venugopal, T.
    Rao, K. Prasad
    Murty, B. S.
    ACTA MATERIALIA, 2007, 55 (13) : 4439 - 4445
  • [25] The synthesis and structure of nanocrystalline spinel ferrite produced by high-energy ball-milling method
    Sepelak, V
    Rogachev, AY
    Steinike, U
    Uecker, DC
    Krumeich, F
    Wissmann, S
    Becker, KD
    SYNTHESIS AND PROPERTIES OF MECHANICALLY ALLOYED AND NANOCRYSTALLINE MATERIALS, PTS 1 AND 2 - ISMANAM-96, 1997, 235-2 : 139 - 144
  • [26] A High-Energy Ball Milling as a Useful Technique for the Synthesis of CaCu3Ti4O12 Electroceramics
    Dulian, P.
    Bak, W.
    Kajtoch, Cz
    Wieczorek-Ciurowa, K.
    ACTA PHYSICA POLONICA A, 2014, 126 (04) : 931 - 937
  • [27] Solvent-Free Mechanochemical Synthesis of ZnO Nanoparticles by High-Energy Ball Milling of ε-Zn(OH)2 Crystals
    Otis, Gil
    Ejgenberg, Michal
    Mastai, Yitzhak
    NANOMATERIALS, 2021, 11 (01) : 1 - 12
  • [28] Using high-temperature mechanochemistry treatment to modify iron oxide and improve the corrosion performance of epoxy coating - I. High-temperature ball milling treatment
    Liu, Xiaoling
    Shao, Yawei
    Zhang, Yingjun
    Meng, Guozhe
    Zhang, Tao
    Wang, Fuhui
    CORROSION SCIENCE, 2015, 90 : 451 - 462
  • [29] Structure and high-temperature oxidation behaviour of Cu-Ni-Fe alloys prepared by high-energy ball milling for application as inert anodes in aluminium electrolysis
    Helle, S.
    Pedron, M.
    Assouli, B.
    Davis, B.
    Guay, D.
    Roue, L.
    CORROSION SCIENCE, 2010, 52 (10) : 3348 - 3355
  • [30] Photocatalytic antibacterial properties of copper doped TiO2 prepared by high-energy ball milling
    Wang, Mei
    Zhao, Qianfei
    Yang, He
    Shi, Dai
    Qian, Juncen
    CERAMICS INTERNATIONAL, 2020, 46 (10) : 16716 - 16724