Influence of the surface finishing on the wear behaviour of cemented carbides worked by Electrical Discharge Machining

被引:4
作者
Sordetti, F. [1 ]
Magnan, M. [1 ]
Carabillo, A. [1 ,2 ]
Querini, M. [2 ]
Fedrizzi, L. [1 ]
Lanzutti, A. [1 ]
机构
[1] Univ Udine, Polytech Dept Engn & Architecture, Via Sci 208, I-33100 Udine, UD, Italy
[2] EUROLLS SpA, Via Ortolani 54, I-33040 Attimis, UD, Italy
关键词
Cermet; Surface finishing; EDM; Wear; WC-CO; MECHANICAL-PROPERTIES; SLIDING WEAR; EDM PARAMETERS; MICROSTRUCTURE; FRICTION; PERFORMANCE; COMPOSITES; ABRASION; CERMETS;
D O I
10.1016/j.ijrmhm.2023.106196
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Cermets are materials, usually made of hard ceramic particles embedded in metal matrix, widely used in different technological fields typically produced by powder metallurgy processes. The combination of the two materials results in a material with superior properties respect to either material alone. One of the most used technology to obtain the final shape of the cermets is the Electrical Discharge Machining process (EDM), which involve some microstructural alterations that influence the tribological behaviour. In this work, several cermet samples were processed using the EDM process. The samples were then subjected to different surface finishing processes such as sandblasting, grinding, lapping and their combinations to reduce the effect of the EDM altered surface layer. The near surface of the samples was analysed in terms of: microstructure (SEM + EDX), surface texture (stylus profilometer), chemical composition (RF-GDOES). A detailed tribological characterization was performed in ballon-flat configuration at several different loads (20 N, 40 N, 80 N) in order to simulate similar conditions of cold rolling rolls. The worn samples were then characterized in order to measure the wear rate and identify the wear mechanisms.The obtained results showed that the EDM process leaves an altered layer that alters the surface of the samples and influences the wear performance of the sample. The removal of this layer completely change the tribological material response in terms of wear rate and coefficient of friction.
引用
收藏
页数:16
相关论文
共 50 条
  • [21] Surface modification by electrical discharge machining: A review
    Kumar, Sanjeev
    Singh, Rupinder
    Singh, T. P.
    Sethi, B. L.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (08) : 3675 - 3687
  • [22] Experimental Analysis and Surface Morphology of Holes Made by Electrical Discharge Machining on MoSi2-SiC Composite
    Selvarajan, L.
    Rajavel, R.
    Arun, C.
    Raju, C.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024, 33 (22) : 12375 - 12397
  • [23] Towards understanding the influence of process parameters during the abrasive jet machining of cemented carbides via response surface method
    Hu, Yan
    Zhang, Jincheng
    Liu, Youyu
    Pan, Jiabao
    JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2024, 46 (12)
  • [24] Influence of superimposed pulse position in superimposed pulse current waveform on surface integrity in electrical discharge machining
    Wang, Guisen
    Han, Fuzhu
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 132 (7-8) : 3179 - 3191
  • [25] Empirical modeling and optimization of kerf and wire wear ratio in wire electrical discharge machining
    Prasad, D. V. S. S. S. V.
    Krishna, A. Gopala
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 77 (1-4) : 427 - 441
  • [26] Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
    Abdulkareem, Suleiman
    Khan, Ahsan Ali
    Konneh, Mohamed
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2009, 45 (11-12) : 1146 - 1151
  • [27] Influence of machining parameters on wire electrical discharge machining performance of reduced graphene oxide/magnesium composite and its surface integrity characteristics
    Kavimani, V.
    Prakash, K. Soorya
    Thankachan, Titus
    COMPOSITES PART B-ENGINEERING, 2019, 167 : 621 - 630
  • [28] Initial surface failure and wear of cemented carbides in sliding contact with different rock types
    Heinrichs, Jannica
    Olsson, Mikael
    Almqvist, Bjarne
    Jacobson, Staffan
    WEAR, 2018, 408 : 43 - 55
  • [29] Study on high wear resistance surface texture of electrical discharge machining based on a new water-in-oil working fluid
    Ji, Renjie
    Zhao, Qingyang
    Zhao, Lilong
    Liu, Yonghong
    Jin, Hui
    Wang, Lixin
    Wu, Lujun
    Xu, Zhiqian
    TRIBOLOGY INTERNATIONAL, 2023, 180
  • [30] Effect of Tool Electrode Resolidification on Surface Hardness in Electrical Discharge Machining
    Muthuramalingam, T.
    Mohan, B.
    Jothilingam, A.
    MATERIALS AND MANUFACTURING PROCESSES, 2014, 29 (11-12) : 1374 - 1380