Thermomechanical Treatment Performance and Flow Stress Model of a Fe-Mn-Al-C Low-Density Steel

被引：4
作者：
Wang, Weijun [1 ]
Zhang, Bendao [1 ]
Cen, Qiongying [1 ]
Zhang, Mei [1 ]
Man, Tinghui [1 ]
Dong, Han [1 ]
机构：
[1] Shanghai Univ, Sch Mat & Sci Engn, Shanghai 200444, Peoples R China
来源：
STEEL RESEARCH INTERNATIONAL | 2023年 / 94卷 / 03期
基金：
国家重点研发计划; 中国国家自然科学基金;
关键词：
Fe-Mn-Al-C low-density steel; flow stress model; hot-processing map; thermomechanical treatment; HOT DEFORMATION-BEHAVIOR; DYNAMIC RECRYSTALLIZATION; CONSTITUTIVE ANALYSIS; TENSILE PROPERTIES; STAINLESS-STEEL; PROCESSING MAP; TWIP STEELS; MICROSTRUCTURE; COMPRESSION; WORKABILITY;
D O I：
10.1002/srin.202200544
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
The flow stress curves of Fe-31.7Mn-11.5Al-0.9C low-density steel are obtained by a hot-compression test with a Gleeble-3500 thermomechanical simulator. It is shown in the results that the dynamic recovery and dynamic recrystallization (DRX) of delta-ferrite occur preferentially under the same deformation condition, inducing a "yield point-like" phenomenon in the true stress-strain curves. The Zener-Hollomon parameter is introduced to fit the characteristic parameters used to establish the flow stress model according to Arrhenius hyperbolic sine relationship and Avrami equation, and the DRX activation energy of austenite is 414.12 KJ mol(-1). The hot-processing maps at different true strains are simulated based on the dynamic material model to determine the suitable hot-rolling process and the optimal hot-working process selection of high strain rate and high deformation temperature combination, 1100-950 degrees C/1-0.2 s(-1), is recommended.
引用
收藏
页数：11
相关论文
共 49 条
[11]   Deformation mechanisms in high-Al bearing high-Mn TWIP steels in hot compression and in tension at low temperatures [J].
Hamada, A. S. ;
Karjalainen, L. P. ;
Somani, M. C. ;
Ramadan, R. M. .
FUNDAMENTALS OF DEFORMATION AND ANNEALING, 2007, 550 :217-+
[12]   Recrystallization behavior in a low-density high-Mn high-Al austenitic steel undergone thin strip casting process [J].
Ji, Fengqin ;
Song, Wenwen ;
Ma, Yan ;
Li, Chengning ;
Bleck, Wolfgang ;
Wang, Guodong .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 733 :87-97
[13]   Fe-Al-Mn-C lightweight structural alloys: a review on the microstructures and mechanical properties [J].
Kim, Hansoo ;
Suh, Dong-Woo ;
Kim, Nack J. .
SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS, 2013, 14 (01)
[14]   Hot Deformation and Dynamic Recrystallization Behavior of Austenite-Based Low-Density Fe-Mn-Al-C Steel [J].
Li, Ya-Ping ;
Song, Ren-Bo ;
Wen, Er-Ding ;
Yang, Fu-Qiang .
ACTA METALLURGICA SINICA-ENGLISH LETTERS, 2016, 29 (05) :441-449
[15]   Microstructure and mechanical properties of an Fe-Mn-Al-C lightweight steel after dynamic plastic deformation processing and subsequent aging [J].
Li, Zongyuan ;
Wang, Ying Chun ;
Cheng, Xingwang ;
Gao, Chong ;
Li, Zhuang ;
Langdon, Terence G. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 833
[16]   Dynamic recrystallization and precipitation behaviors during hot deformation of a κ-carbide-bearing multiphase Fe-11Mn-10Al-0.9C lightweight steel [J].
Liu, Degang ;
Ding, Hua ;
Hu, Xiao ;
Han, Dong ;
Cai, Minghui .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 772
[17]   Hot Deformation Behavior and Processing Map of a Fe-11Mn-10Al-0.9C Duplex Low-Density Steel Susceptible to κ-Carbides [J].
Liu, Degang ;
Ding, Hua ;
Cai, Minghui ;
Han, Dong .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2019, 28 (08) :5116-5126
[18]   A simple method to produce austenite-based low-density Fe-20Mn-9Al-0.75C steel by a near-rapid solidification process [J].
Liu, Libing ;
Li, Chunming ;
Yang, Yang ;
Luo, Zhiping ;
Song, Changjiang ;
Zhai, Qijie .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 679 :282-291
[19]   The effect of rare earth alloying on the hot workability of duplex stainless steel - A study using processing map [J].
Ma, Xiaocong ;
An, Zijun ;
Chen, Lei ;
Mao, Tianqiao ;
Wang, Jianfeng ;
Long, Hongjun ;
Xue Hongyan .
MATERIALS & DESIGN, 2015, 86 :848-854
[20]   Effect of cooling rate on the precipitation behavior of.-carbide in Fe-32Mn-11Al-0.9C low density steel [J].
Man, Tinghui ;
Wang, Weijun ;
Zhou, Yihao ;
Liu, Tengshi ;
Lu, Hengchang ;
Zhao, Xiuming ;
Zhang, Mei ;
Dong, Han .
MATERIALS LETTERS, 2022, 314
12345