Evidence supporting reversible martensitic transformation under cyclic loading on Fe-Mn-Si-Al alloys using in situ neutron diffraction

被引:19
作者
Sawaguchi, Takahiro [1 ]
Tomota, Yo [1 ,2 ]
Yoshinaka, Fumiyoshi [1 ]
Harjo, Stefanus [3 ]
机构
[1] Natl Inst Mat Sci, Res Ctr Struct Mat, 1-2-1 Sengen, Tsukuba, Ibaraki 3050047, Japan
[2] Natl Inst Adv Ind Sci & Technol, Cent 2,1-1-1 Umezono, Tsukuba, Ibaraki 3068568, Japan
[3] Japan Atom Energy Agcy, J PARC Ctr, 2-4 Shirakata, Tokai, Ibaraki 3191195, Japan
基金
日本科学技术振兴机构; 日本学术振兴会;
关键词
Plastic fatigue; Fe-Mn-Si-Al alloys; In situ neutron diffraction; epsilon-Martensite; Reversible martensitic transformation; INDUCED EPSILON-MARTENSITE; SHAPE-MEMORY ALLOYS; FATIGUE RESISTANCE; INDUCED PLASTICITY; STRAIN; DEFORMATION; BEHAVIOR; PHASE; MICROSTRUCTURE; STRESS;
D O I
10.1016/j.actamat.2022.118494
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Fe-Mn-Si-based alloys, such as Fe-30Mn-4Si-2Al and Fe-15Mn-10Cr-8Ni-4Si (in mass%), show superior resistance to plastic fatigue compared to the conventional steels, which is ascribed to the reversible back-and-forth movement of {111}< 11 (2) over bar >(gamma) Shockley partial dislocations associated with a reversible martensitic transformation between the face-centered cubic gamma-austenite and hexagonal close-packed epsilon-martensite. The purpose of this study was to gather evidence of the reversible martensitic transformation using in situ neutron diffraction under cyclic loading. Three Fe-30Mn-Si-Al alloys with different Gibbs free energy differences at 298 K: Fe-30Mn-6Si (Delta G(gamma ->epsilon) = -250 J/mol), Fe-30Mn-55i-1Al (Delta G(gamma ->epsilon)( )= -128 J/mol), and Fe-30Mn-45i-2Al (Delta G(gamma ->epsilon )= -8.5 J/mol), were studied to unravel the effect of phase stability on the degree of reversibility. The reversible martensitic transformation between gamma-austenite and epsilon-martensite during tension-compression loading is demonstrated as bulk-averaged insights in the Fe-30Mn-45i-2Al alloy. The forward gamma -> epsilon transformation was induced by tensile loading, and the formed epsilon plates were reversed to gamma during unloading and subsequent compressive loading. Furthermore, successive compressive loading induced a different variant of the epsilon plates from the variant formed under tensile loading, which also reverted to gamma by subsequent tensile loading. Such repetition of the gamma <-> epsilon transformation in the Fe-30Mn-45i-2Al alloy is thought to increase the plastic fatigue life compared to the Fe-30Mn-6Si and Fe-30Mn-Si-1Al alloys, in which the gamma <-> epsilon transformation is rarely reversible. Herein, we discuss the mechanism of the deformation-induced reverse transformation and propose an optimum thermodynamic condition: a negative close-to-zero Delta G(gamma ->epsilon ) . (C) 2022 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
引用
收藏
页数:14
相关论文
共 66 条
[31]   THE EFFECT OF SLIP BEHAVIOR ON THE LOW-CYCLE FATIGUE BEHAVIOR OF 2 AUSTENTIC STAINLESS-STEELS [J].
NILSSON, JO .
SCRIPTA METALLURGICA, 1983, 17 (05) :593-596
[32]   Internal stress and strain energy yielded by γ → ε martensitic transformation in a polycrystalline ferrous alloy [J].
Nozaki, H ;
Tomota, Y .
MATERIALS TRANSACTIONS JIM, 2000, 41 (06) :727-732
[33]   Rietveld analysis software for J-PARC [J].
Oishi, R. ;
Yonemura, M. ;
Nishimaki, Y. ;
Torii, S. ;
Hoshikawa, A. ;
Ishigaki, T. ;
Morishima, T. ;
Mori, K. ;
Kamiyama, T. .
NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT, 2009, 600 (01) :94-96
[34]  
Otsuka K., 1999, Shape memory materials
[35]   Fe-Mn-Si-Cr-Ni based shape memory alloy: Thermal and stress-induced martensite [J].
Pan, Ming-Ming ;
Zhang, Xiao-Ming ;
Zhou, Ding ;
Misra, R. D. K. ;
Chen, Peng .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 797
[36]   On the significance of C and Co on shape memory performance of Fe-Mn-Si-Cr-Ni shape memory alloy [J].
Pan, Ming-Ming ;
Zhang, Xiao-Ming ;
Zhou, Ding ;
Misra, R. D. K. ;
Chen, Peng ;
Su, Xiang-Bin .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 786
[37]   CRITERION FOR THE ACTION OF APPLIED STRESS IN THE MARTENSITIC TRANSFORMATION [J].
PATEL, JR ;
COHEN, M .
ACTA METALLURGICA, 1953, 1 (05) :531-538
[38]   The influence of manganese content on the stacking fault and austenite/ε-martensite interfacial energies in Fe-Mn-(Al-Si) steels investigated by experiment and theory [J].
Pierce, D. T. ;
Jimenez, J. A. ;
Bentley, J. ;
Raabe, D. ;
Oskay, C. ;
Wittig, J. E. .
ACTA MATERIALIA, 2014, 68 :238-253
[39]   Mechanical properties of low yield point steels [J].
Saeki, E ;
Sugisawa, M ;
Yamaguchi, T ;
Wada, A .
JOURNAL OF MATERIALS IN CIVIL ENGINEERING, 1998, 10 (03) :143-152
[40]   PHYSICAL-PROPERTIES CONTROLLING SHAPE MEMORY EFFECT IN FE-MN-SI ALLOYS [J].
SATO, A ;
YAMAJI, Y ;
MORI, T .
ACTA METALLURGICA, 1986, 34 (02) :287-294