Fused Filament Fabrication of cellular, lattice and porous mechanical metamaterials: a review

被引:40
作者
Cuan-Urquizo, Enrique [1 ]
Silva, Rafael Guerra [2 ,3 ]
机构
[1] Tecnol Monterrey, Inst Adv Mat Sustainable Mfg, Monterrey, Mexico
[2] Calif State Polytech Univ, Ind Technol & Packaging, San Luis Obispo, CA USA
[3] Calif State Polytech Univ, Ind Technol & Packaging, 1 Grand Ave, San Luis Obispo, CA 93407 USA
关键词
Additive manufacturing; cellular materials; lattice structures; metamaterials; Fused Filament Fabrication; FATIGUE BEHAVIOR; TOPOLOGY OPTIMIZATION; COMPRESSIVE BEHAVIOR; 3D; FDM; SCAFFOLDS; DESIGN; PERFORMANCE; HONEYCOMBS; MANUFACTURE;
D O I
10.1080/17452759.2023.2224300
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
One of the areas that have benefited the most from the advent of additive manufacturing is the development of customized cellular materials, scaffolds and lattices. Although these different groups of materials are typically considered separately, they can be categorized as mechanical metamaterials. Among the different additive manufacturing techniques, perhaps the most popular is that of Fused Filament Fabrication. Numerous works have been reported in the literature in which this fabrication technique has been used to produce such materials. Inspired by the increasing volume of work dealing with the subject, we present a review of the manufacturing and characterization of cellular and lattice-based mechanical metamaterials using Fused Filament Fabrication. An overview of the topologies, their effective mechanical properties and intrinsic manufacturing aspects are presented. The methods for failure analysis at different scales are also discussed. Finally, studies comparing the production of mechanical metamaterials using Fused Filament Fabrication and other additive manufacturing techniques are presented, in addition to recommendations and current trends in the production of these structures by Fused Filament Fabrication.
引用
收藏
页数:40
相关论文
共 198 条
[1]   Effect of strut length and orientation on elastic mechanical response of modified body-centered cubic lattice structures [J].
Abdulhadi, Hasanain S. ;
Mian, Ahsan .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS, 2019, 233 (11) :2219-2233
[2]   Effect of Architected Structural Members on the Viscoelastic Response of 3D Printed Simple Cubic Lattice Structures [J].
Abusabir, Ahmed ;
Khan, Muhammad A. ;
Asif, Muhammad ;
Khan, Kamran A. .
POLYMERS, 2022, 14 (03)
[3]   Hierarchical honeycombs with tailorable properties [J].
Ajdari, Amin ;
Jahromi, Babak Haghpanah ;
Papadopoulos, Jim ;
Nayeb-Hashemi, Hamid ;
Vaziri, Ashkan .
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES, 2012, 49 (11-12) :1413-1419
[4]   Effect of Filling Pattern on the Tensile and Flexural Mechanical Properties of FDM 3D Printed Products [J].
Akhoundi, B. ;
Behravesh, A. H. .
EXPERIMENTAL MECHANICS, 2019, 59 (06) :883-897
[5]   Design of Hierarchical Architected Lattices for Enhanced Energy Absorption [J].
Al Nashar, Mohamad ;
Sutradhar, Alok .
MATERIALS, 2021, 14 (18)
[6]   Compression behavior of three-dimensional printed polymer lattice structures [J].
Al Rifaie, Mohammed ;
Mian, Ahsan ;
Srinivasan, Raghavan .
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART L-JOURNAL OF MATERIALS-DESIGN AND APPLICATIONS, 2019, 233 (08) :1574-1584
[7]  
Alizadeh-Osgouei Mona., Smart Materials in Medicine, V2, P15, DOI DOI 10.1016/J.SMAIM.2020.10.003
[8]   On the mechanical properties of atomic and 3D printed zeolite-templated carbon nanotube networks [J].
Ambekar, Rushikesh S. ;
Oliveira, Eliezer F. ;
Kushwaha, Brijesh ;
Pal, Varinder ;
Machado, Leonardo D. ;
Sajadi, Seyed Mohammad ;
Baughman, Ray H. ;
Ajayan, Pulickel M. ;
Roy, Ajit K. ;
Galvao, Douglas S. ;
Tiwary, Chandra S. .
ADDITIVE MANUFACTURING, 2021, 37
[9]   Analytical and Experimental Investigation into the Relative Influence of Core and Side Parts on Structures Laminated by Fused Deposition Modeling [J].
An, Da-Sol ;
Kim, Tae Hyun ;
Lee, Eun-Ho .
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY, 2021, 8 (01) :13-27
[10]  
[Anonymous], 2021, ISO/ASTM Standard 52900:2021(E)