Effect of externally applied magnetic field on the tool wear and surface morphology of Inconel 718 in turning operation

被引：2

作者：

Waghmode, Sukhdev B. ^{[1
]}

Kallol, Anupama N. ^{[1
]}

Shivakumar, S. ^{[1
]}

Manjunath, G. A. ^{[1
]}

Doiphode, Rajendra L. ^{[2
]}

Chandrashekar, A. ^{[3
]}

Omprakash, B. ^{[4
]}

Razak, Abdul ^{[5
,7
]}

Hasan, Nasim ^{[6
,8
]}

机构：

[1] KLS Gogte Inst Technol, Dept Mech Engn, Belagavi, India

[2] Govt Polytech, Dept Mech Engn, Kolhapur, India

[3] Bangalore Inst Technol, Dept Mech Engn, Bengaluru, India

[4] JNTUA Coll Ananthapuram, Dept Mech Engn, Anantapur, India

[5] Visvesvaraya Technol Univ, P A Coll Engn, Dept Mech Engn, Belagavi, India

[6] Mattu Univ, Mech Engn Dept, Mettu Oromia, Ethiopia

[7] PA Coll Engn, Mangalore, India

[8] Mattu Univ, Mech Engn Dept, POB 318, Mettu Oromia, Ethiopia

来源：

ENGINEERING REPORTS | 2024年 / 6卷 / 01期

关键词：

Inconel; 718; magnetic field; surface roughness; tool wear; turning; REDUCTION;

D O I：

10.1002/eng2.12700

中图分类号：

TP39 [计算机的应用];

学科分类号：

081203 ; 0835 ;

摘要：

This study examined the effect of magnetic field with single point coated-carbide tool during turning process of Inconel718 (In718). After the turning process, tribological properties (surface roughness and tool wear) and chip morphology were analyzed. Two cylindrical Neodymium (N52) grade permanent magnets are used to apply the magnetic field during the machining. Cutting speed and magnetic field intensity along with constant feed and depth of cut are used to analyze tribological properties along with chip morphology. Experimental results show that 80 m/min cutting speed and 426 Gauss magnetic field has the best results in term of lowest surface roughness and tool wear. Lorentz forces developed due to the applied external magnetic field help to improve surface roughness compared to nonmagnetic field machining. Developed fine particles during the turning process get repulsed in case of magnetic field machining which helps to improve tool wear.

引用

页数：16

共 29 条

[21] Effect of novel hybrid texture tool on turning process performance in MQL machining of Inconel 718 superalloy [J].

Sivaiah, P. ;

Ajay Kumar, Venakata G. ;

Singh, Muralidhar M. ;

Kumar, Harinandan .

MATERIALS AND MANUFACTURING PROCESSES, 2020, 35 (01) :61-71

[22] Sustainability in machining: "Eco-friendly" turning of Inconel 718. Surface characterisation and economic analysis [J].

Tebaldo, Vincenzo ;

di Confiengo, Giovanna Gautier ;

Faga, Maria Giulia .

JOURNAL OF CLEANER PRODUCTION, 2017, 140 :1567-1577

[23] Machinability improvement of Inconel 718 through mechanochemical and heat transfer effects of coated surface-active thermal conductive mediums [J].

Yin, Qingan ;

Liu, Zhanqiang ;

Wang, Bing .

JOURNAL OF ALLOYS AND COMPOUNDS, 2021, 876

[24] Reduction of tool tip vibration in single-point diamond turning using an eddy current damping effect [J].

Yip, W. S. ;

To, S. .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 103 (5-8) :1799-1809

[25] Effects of magnetic field on microstructures and mechanical properties of titanium alloys in ultra-precision diamond turning [J].

Yip, W. S. ;

To, S. .

MATERIALS RESEARCH EXPRESS, 2019, 6 (05)

[26] Reduction of material swelling and recovery of titanium alloys in diamond cutting by magnetic field assistance [J].

Yip, W. S. ;

To, S. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2017, 722 :525-531

[27] Enhancing cutting performance of uncoated cemented carbide tools by joint-use of magnetic nanofluids and micro-texture under magnetic field [J].

Zhang, Liang ;

Guo, Xuhong ;

Zhang, Kedong ;

Wu, Yongqiang ;

Huang, Qiang .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2020, 284

[28] Coating-thickness-dependent physical properties and cutting temperature for cutting Inconel 718 with TiAlN coated tools [J].

Zhao, Jinfu ;

Liu, Zhanqiang ;

Ren, Xiaoping ;

Wang, Bing ;

Cai, Yucui ;

Song, Qinghua ;

Wan, Yi .

JOURNAL OF ADVANCED RESEARCH, 2022, 38 :191-199

[29] Influences of coating thickness on cutting temperature for dry hard turning Inconel 718 with PVD TiAlN coated carbide tools in initial tool wear stage [J].

Zhao, Jinfu ;

Liu, Zhanqiang .

JOURNAL OF MANUFACTURING PROCESSES, 2020, 56 (56) :1155-1165

← 1 2 3 →