Application of novel constrained friction processing method to produce fine grained biomedical Mg-Zn-Ca alloy

被引：17

作者：

Chen, Ting ^{[1
]}

Fu, Banglong ^{[1
]}

Shen, Junjun ^{[1
]}

Suhuddin, Uceu F. H. R. ^{[1
]}

Wiese, Bjoern ^{[2
]}

Huang, Yuanding ^{[2
]}

Wang, Min ^{[3
]}

dos Santos, Jorge F. ^{[1
,4
]}

Bergmann, Jean Pierre ^{[5
]}

Klusemann, Benjamin ^{[1
,6
]}

机构：

[1] Helmholtz Zentrum Hereon, Inst Mat Mech, State Mat Proc, Max Planck Str 1, D-21502 Geesthacht, Germany

[2] Helmholtz Zentrum Hereon, Inst Metall Biomat, Funct Magnesium Mat, Max Planck Str 1, D-21502 Geesthacht, Germany

[3] Shanghai Jiao Tong Univ, Shanghai Key Lab Mat Laser Proc & Modificat, Dongchuan Rd 800, Shanghai 200240, Peoples R China

[4] Pacific Northwest Natl Lab, Div Energy & Environm, Appl Mat & Mfg, POB 999, Richland, WA 99352 USA

[5] Tech Univ Ilmenau, Prod Technol Grp, Gustav Kirchhoff Pl 2, D-98693 Ilmenau, Germany

[6] Leuphana Univ Luneburg, Inst Prod Technol & Syst, Univ Allee 1, D-21335 Luneburg, Germany

来源：

JOURNAL OF MAGNESIUM AND ALLOYS | 2024年 / 12卷 / 02期

关键词：

Constrained friction processing; Magnesium alloys; Microstructure; Mechanical properties; Grain refinement; Plastic deformation; BIO-CORROSION RESISTANCE; MECHANICAL-PROPERTIES; DYNAMIC RECRYSTALLIZATION; MAGNESIUM ALLOYS; MICROSTRUCTURE; BEHAVIOR; STRENGTH; SIZE; REFINEMENT; TEXTURE;

D O I：

10.1016/j.jma.2023.10.007

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

In order to obtain Mg alloys with fine microstructures and high mechanical performances, a novel friction-based processing method, name as "constrained friction processing (CFP)", was investigated. Via CFP, defect-free Mg -Zn -Ca rods with greatly refined grains and high mechanical properties were produced. Compared to the previous as-cast microstructure, the grain size was reduced from more than 1 mm to around 4 mu m within 3 s by a single process cycle. The compressive yield strength was increased by 350% while the ultimate compressive strength by 53%. According to the established material flow behaviors by "tracer material", the plastic material was transported by shear deformation. From the base material to the rod, the material experienced three stages, i.e. deformation by the tool, upward flow with additional tilt, followed by upward transportation. The microstructural evolution was revealed by "stop -action" technique. The microstructural development at regions adjacent to the rod is mainly controlled by twinning, dynamic recrystallization (DRX) as well as particle stimulated nucleation, while that within the rod is related to DRX combined with grain growth. (c) 2023 Chongqing University. Publishing services provided by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY license ( http://creativecommons.org/licenses/by/4.0/ ) Peer review under responsibility of Chongqing University

引用

页码：516 / 529

页数：14

共 52 条

[11] Corrosion of Metallic Biomaterials: A Review [J].