Influence of aluminum waste on the thermo-mechanical properties of lightweight composite mortars based on sand and recycled high-density polyethylene

被引:0
作者
Haouara, Selma [1 ,2 ]
Zeghichi, Leila [1 ]
Izemmouren, Ouarda [1 ,2 ]
Souici, Ikram [3 ]
机构
[1] Mohamed khider Univ Biskra, Civil Engn Dept, Biskra, Algeria
[2] Mohamed Khider Univ Biskra, Civil Engn Res Lab LRGC, Biskra, Algeria
[3] Univ Guelma, Civil Engn Dept, Guelma, Algeria
关键词
High-density polyethylene; sand; composite mortar; aluminum powder; density; strength; thermal conductivity; PLASTIC WASTE; MECHANICAL-PROPERTIES; AGGREGATE CONCRETE; PET; BEHAVIOR; TEREPHTHALATE; POLYSTYRENE;
D O I
10.1080/19648189.2023.2229396
中图分类号
TU [建筑科学];
学科分类号
0813 ;
摘要
The development of new construction materials must take into consideration several factors, including the environmental impact, cost price, mechanical performance and thermal comfort. The present study falls within this context. It essentially aims to valorize high-density polyethylene plastic waste as a fine aggregate in substitution of sand at 10% and 30% in order to produce lightweight composite mortars. The incorporation of aluminum waste (powder), which is as an expansive agent, was made at 0.5% and 1% of cement weight in order to further lighten the products that are primarily intended for thermal insulation. This study also seeks to investigate properties in the fresh state such as the workability of mortar, and other properties in the hardened state such as the density, the compressive strength and tensile strength by bending, and finally the thermal conductivity. The results obtained showed that the density of the product obtained decreased as a function of the rate of replacement of natural fine aggregates by high-density polyethylene and also of the aluminum content. In addition, it was observed that the mechanical strengths decreased while the thermal conductivity of the composite mortars obtained improved significantly by approximately 48% in comparison with that of the control mortar.
引用
收藏
页码:844 / 858
页数:15
相关论文
共 36 条
  • [31] Use of plastic waste as aggregate in cement mortar and concrete preparation: A review
    Saikia, Nabajyoti
    de Brito, Jorge
    [J]. CONSTRUCTION AND BUILDING MATERIALS, 2012, 34 : 385 - 401
  • [32] Effect of incorporating PVC waste as aggregate on the physical, mechanical, and chloride ion penetration behavior of concrete
    Senhadji, Y.
    Escadeillas, G.
    Benosman, A. S.
    Mouli, M.
    Khelafi, H.
    Kaci, S. Ould
    [J]. JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2015, 29 (07) : 625 - 640
  • [33] Shubbar SD, 2017, Kufa Journal of Engineering, V8, P132, DOI [10.30572/2018/KJE/821171, DOI 10.30572/2018/KJE/821171]
  • [34] Mechanical properties of expanded polystyrene lightweight aggregate concrete and brick
    Xu, Yi
    Jiang, Linhua
    Xu, Jinxia
    Li, Yang
    [J]. CONSTRUCTION AND BUILDING MATERIALS, 2012, 27 (01) : 32 - 38
  • [35] Microstructural characteristics of sound absorbable porous cement-based materials by incorporating natural fibers and aluminum powder
    Yoon, Jinyoung
    Kim, Hyunjun
    Koh, Taehoon
    Pyo, Sukhoon
    [J]. CONSTRUCTION AND BUILDING MATERIALS, 2020, 243 (243)
  • [36] Structural, mechanical and hygrothermal properties of lightweight concrete based on the application of waste plastics
    Zaleska, Martina
    Pavlikova, Milena
    Pokorny, Jaroslav
    Jankovsky, Ondrej
    Pavlik, Zbysek
    Cerny, Robert
    [J]. CONSTRUCTION AND BUILDING MATERIALS, 2018, 180 : 1 - 11