A novel method for improving the microstructure and the properties of Al-Si-Cu alloys prepared using rapid solidification/powder metallurgy

被引：14
|
作者：
Zhao, Xingming [1 ]
Meng, Jingran [1 ]
Zhang, Chi [1 ]
Wei, Wei [1 ]
Wu, Fufa [1 ]
Zhang, Guangan [1 ]
机构：
[1] Liaoning Univ Technol, Sch Mat Sci & Engn, Mat Proc Engn, Jinzhou 121001, Peoples R China
来源：
MATERIALS TODAY COMMUNICATIONS | 2023年 / 35卷
关键词：
Rapid solidification; powder metallurgy; Al; -Si; -Cu; Extrusion; Crushed oxide film; Mechanical properties; ALUMINUM-ALLOYS; TENSILE PROPERTIES; BEHAVIOR; COMPOSITES; PARAMETERS; MECHANISM;
D O I：
10.1016/j.mtcomm.2023.105802
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
A novel method based on the combination of rapid solidification/powder metallurgy with hot extrusion was proposed in the present study for improving the microstructure and properties of Al-Si-Cu alloys. The phase composition, microstructure, and mechanical properties of the extruded Al-Si-Cu alloy were systematically investigated. The experimental results revealed that the extruded Al-Si-Cu alloy comprised five kinds of phases, namely, the & alpha;-Al, fi-Si, Al2O3, CuAl2, and Cu4Si phases. The extrusion process significantly reduced the porosity while improving the density of the Al-Si-Cu alloy. The tensile strength and elongation values of the extruded alloy were much larger than those of the unextruded alloy. The use of the proposed method improved the mechanical properties of the Al-Si-Cu alloy greatly compared to when using the traditional casting method.
引用
收藏
页数：9
相关论文
共 50 条
  • [21] Effect of heat treatment and Fe content on the microstructure and mechanical properties of die-cast Al-Si-Cu alloys
    Yang, Hailin
    Ji, Shouxun
    Fan, Zhongyun
    MATERIALS & DESIGN, 2015, 85 : 823 - 832
  • [22] Microstructure investigation of light weight Al/Si/Ni hypoeutectic material prepared by powder metallurgy method
    Alsowidy, Shakib
    Al-Asry, Belqueis
    Alnehia, Adnan
    RESULTS IN CHEMISTRY, 2024, 7
  • [23] Thermophysical properties and rapid solidification of Al-Cu-Ge alloys
    Wang Xiao-Juan
    Ruan Ying
    Hong Zhen-Yu
    ACTA PHYSICA SINICA, 2014, 63 (09)
  • [24] Microstructure and mechanical properties of hot extruded Mg-Al-Mn-Ca alloy produced by rapid solidification powder metallurgy
    Elsayed, Ayman
    Kondoh, Katsuyoshi
    Imai, Hisashi
    Umeda, Junko
    MATERIALS & DESIGN, 2010, 31 (05): : 2444 - 2453
  • [25] Microstructure and properties of Mo-Cu alloys produced by powder metallurgy
    Wang, T. G.
    Liang, Q. C.
    Qin, Q.
    MATERIALS RESEARCH INNOVATIONS, 2015, 19 : 1150 - 1152
  • [26] Effect of Grain Refinement and Cooling Rate on the Microstructure and Mechanical Properties of Secondary Al-Si-Cu Alloys
    Giulio Timelli
    Giordano Camicia
    Stefano Ferraro
    Journal of Materials Engineering and Performance, 2014, 23 : 611 - 621
  • [27] Effect of Grain Refinement and Cooling Rate on the Microstructure and Mechanical Properties of Secondary Al-Si-Cu Alloys
    Timelli, Giulio
    Camicia, Giordano
    Ferraro, Stefano
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2014, 23 (02) : 611 - 621
  • [28] Effect of Mg level on the microstructure and mechanical properties of die-cast Al-Si-Cu alloys
    Yang, Hailin
    Ji, Shouxun
    Yang, Wenchao
    Wang, Yun
    Fan, Zhongyun
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 642 : 340 - 350
  • [29] PROPERTIES OF NANOCRYSTALLINE Al-Cr-Fe-Ti ALLOYS PREPARED BY POWDER METALLURGY
    Dam, Karel
    Vojtech, Dalibor
    Prusa, Filip
    NANOCON 2012, 4TH INTERNATIONAL CONFERENCE, 2012, : 253 - 258
  • [30] Microstructure and Properties of High Temperature Titanium Alloys with a High Si Content Prepared by Powder Metallurgy
    Kuang, Q. B.
    Zou, L. M.
    Cai, Y. X.
    Liu, X.
    Xie, H. W.
    MATERIALS TRANSACTIONS, 2017, 58 (12) : 1735 - 1741
12345