Influence of Protective Coatings of Inserts on Cutting Forces during Milling of Hadfield Steel

被引：1

作者：

Pyatykh, A. S. ^{[1
]}

Savilov, A. V. ^{[1
]}

Timofeev, S. A. ^{[1
]}

Svinin, V. M. ^{[1
]}

Maizel, I. G. ^{[1
]}

机构：

[1] Irkutsk Natl Res Tech Univ, Irkutsk 664074, Russia

来源：

JOURNAL OF FRICTION AND WEAR | 2023年 / 44卷 / 03期

关键词：

Hadfield steel; milling; cutting forces; coefficient of friction; Taguchi method; analysis of variance; regression analysis; protective coatings; cutting modes; hard alloy; SURFACE-ROUGHNESS; OPTIMIZATION; OPERATION;

D O I：

10.3103/S1068366623030078

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The present study analyzed the effect of protective coatings of replaceable hard-alloy plates on cutting forces when milling austenitic high-manganese Hadfield (110G13L) steel. S30T, 1130, S40T, and 4240 hard alloys with PVD and CVD coatings were explored. The analysis was conducted on a milling machining center with a dynamometer plate installed on the table. The experiment was based on the orthogonal planning matrix. The Taguchi method was employed to identify a coating with the best properties. The analysis of variance showed that the tool feed has the greatest effect on active cutting forces. The specific feed gravity was 65.22%. The regression analysis revealed that to minimize and predict cutting forces for the entire range of cutting conditions, S30T alloy with a protective TiAlN PVD coating is preferable in machining austenitic 110G13L stainless steel. The results can improve the machining efficiency for Hadfield steel products produced by machine-building enterprises.

引用

页码：156 / 163

页数：8

共 50 条

[31] Analysis of the influence of cutting parameters on surface roughness and cutting forces in high speed face milling of Al/SiC MMC
Ghoreishi, R.
Roohi, Amir H.
Ghadikolaei, A. Dehghan
MATERIALS RESEARCH EXPRESS, 2018, 5 (08):
[32] ExPERIMENTAL AND NUMERICAL INvESTIGATION OF CUTTING FORCES AND TEMPERATURES IN MILLING OF CUSTOM 450 STEEL
Gokce, Harun
ARCHIVES OF METALLURGY AND MATERIALS, 2022, 67 (03) : 843 - 853
[33] Three Dimensional Finite Element Simulation of Cutting Forces and Cutting Temperature in Hard Milling of AISI H13 Steel
Zhang, Qing
Zhang, Song
Li, Jianfeng
45TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 45), 2017, 10 : 37 - 47
[34] Influence of cutting parameters on cutting forces in high speed milling of thin walled graphite electrode
Hu Zhouling
Wang Chengyong
Zhou Li
Fu Hao
PROGRESS OF MACHINING TECHNOLOGY, PROCEEDINGS, 2006, : 341 - 344
[35] Analysis of influence of variation of cutting forces direction on accuracy of curvature representation by profile milling operation
Grzesiak, D. D.
Krolikowski, M. A.
Annals of DAAAM for 2005 & Proceedings of the 16th International DAAAM Symposium: INTELLIGENT MANUFACTURING & AUTOMATION: FOCUS ON YOUNG RESEARCHES AND SCIENTISTS, 2005, : 149 - 150
[36] Cutting Forces during Inconel 718 Orthogonal Turn-Milling
Felusiak-Czyryca, Agata
Madajewski, Marek
Twardowski, Pawel
Wiciak-Pikula, Martyna
MATERIALS, 2021, 14 (20)
[37] Characteristic variations of chip morphology and cutting forces in face milling with flat-faced and grooved tool inserts
Fang, N
JSME INTERNATIONAL JOURNAL SERIES A-SOLID MECHANICS AND MATERIAL ENGINEERING, 2003, 46 (03) : 230 - 236
[38] Influence of tool tilting angles on cutting forces and tool deflection in ball end milling (1 st report) - Geometric quantities and cutting forces in slot milling with tool tilted by one or two axes
Kasahara K.
Murata K.
Suzuki C.
Hirota A.
Seimitsu Kogaku Kaishi/Journal of the Japan Society for Precision Engineering, 2011, 77 (10): : 966 - 971
[39] The Influence of Surface Roughness of Cutting Inserts Made of Diamond–Tungsten Carbide Composite on Cutting Forces and Machining Quality in Turning Aluminum Alloys and Brass
L. N. Devin
N. E. Stakhniv
Yu. A. Mel’niichuk
Journal of Superhard Materials, 2018, 40 : 131 - 137
[40] The influence of different PVD coatings techniques on cutting forces in a drilling process
Benga, G.
PROCEEDINGS OF THE 6TH INTERNATIONAL CONFERENCE OF DAAAM BALTIC INDUSTRIAL ENGINEERING, PTS 1 AND 2, 2008, : 407 - 412

← 1 2 3 4 5 →