Microstructures and mechanical properties of TA1 sintered samples prepared by injection molding using water-soluble binder

被引：0

作者：

Zhang, Weichen ^{[1
]}

Li, Lu ^{[1
,2
,6
]}

Cao, Peng ^{[3
]}

Chen, Gang ^{[4
]}

Hayat, Muhammad Dilawer ^{[5
]}

机构：

[1] Kunming Univ Sci & Technol, Fac Mat Sci & Engn, Kunming, Peoples R China

[2] Kunming Univ Sci & Technol, Res Ctr Anal & Measurement, Kunming, Peoples R China

[3] Univ Auckland, Fac Engn Chem & Mat Engn, Auckland, New Zealand

[4] Univ Sci & Technol Beijing, Fac Mat Sci & Engn, Beijing, Peoples R China

[5] Univ Waikato, Fac Engn, Hamilton, New Zealand

[6] Kunming Univ Sci & Technol, Fac Mat Sci & Engn, Kunming 650093, Peoples R China

来源：

JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY | 2024年 / 38卷 / 15期

关键词：

Water-soluble binder; injection molding; sintering temperature; mechanical properties; carbon and oxygen contents; PURE TITANIUM; OXYGEN CONCENTRATION; BEHAVIOR; SYSTEM;

D O I：

10.1080/01694243.2024.2320502

中图分类号：

TQ [化学工业];

学科分类号：

0817 ;

摘要：

A water-soluble binder was used to obtain TA1 sintered samples prepared by injection molding. The effects of the sintering temperature on the microstructures and mechanical properties of the sintered samples were analyzed. A relative density of >91% is achieved. Some residual carbon and oxygen remain in the sintered samples, affecting the mechanical properties. The tensile strength and elongation of the sample sintered at 1,300 C-degrees are the highest: 592 MPa and 12.95%, respectively. Detailed electron microscopic analysis was performed to identify the morphology and nature of the resultant titanium carbides and oxides.

引用

页码：2856 / 2873

页数：18

共 37 条

[1] Modeling of interstitials diffusion during debinding/sintering of 3D printed metallic filaments: Application to titanium alloy and its embrittlement
Coffigniez, M.
Gremillard, L.
Perez, M.
Simon, S.
Rigollet, C.
Bonjour, E.
Jame, P.
Boulnat, X.
[J]. ACTA MATERIALIA, 2021, 219
[2] Metal injection moulding of non-spherical titanium powders: Processing, microstructure and mechanical properties
Dehghan-Manshadi, A.
StJohn, D.
Dargusch, M.
Chen, Y.
Sun, J. F.
Qian, M.
[J]. JOURNAL OF MANUFACTURING PROCESSES, 2018, 31 : 416 - 423
[3] Metal injection moulding of titanium and titanium alloys: Challenges and recent development
Dehghan-Manshadi, A.
Bermingham, M. J.
Dargusch, M. S.
StJohn, D. H.
Qian, M.
[J]. POWDER TECHNOLOGY, 2017, 319 : 289 - 301
[4] Powder injection molding of pure titanium
Guo Shibo
Duan Bohua
He Xinbo
Qu Xuanhui
[J]. RARE METALS, 2009, 28 (03) : 261 - 265
[5] Influence of firing conditions and production methods on fracture strength of titanium-based metal ceramic crowns
Haag, P.
Khan, F.
Andersson, M.
von Steyern, P. Vult
[J]. JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY, 2018, 32 (03) : 225 - 238
[6] Modification of PEG/PMMA binder by PVP for titanium metal injection moulding
Hayat, Muhammad Dilawer
Goswami, Aparajita
Matthews, Steven
Li, Tao
Yuan, Xiaowen
Cao, Peng
[J]. POWDER TECHNOLOGY, 2017, 315 : 243 - 249
[7] Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC
He, Ni
Li, Mingjia
Sun, Guodong
Xu, Junjie
Li, Mingyang
Dong, Longlong
Zhang, Yusheng
[J]. METALS, 2023, 13 (05)
[8] Titanium and titanium alloys in dentistry: current trends, recent developments, and future prospects
Hoque, Md Enamul
Showva, Nazmir-Nur
Ahmed, Mansura
Bin Rashid, Adib
Sadique, Sarder Elius
El -Bialy, Tarek
Xu, Huaizhong
[J]. HELIYON, 2022, 8 (11)
[9] A Comprehensive Review on Machining of Titanium Alloys
Hourmand, Mehdi
Sarhan, Ahmed A. D.
Sayuti, Mohd
Hamdi, Mohd
[J]. ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2021, 46 (08) : 7087 - 7123
[10] Effects of oxygen content on Charpy impact properties and crack resistance of α titanium alloys
Huang, Shixing
Zhao, Qinyang
Lin, Cheng
Wu, Cong
Zhao, Yongqing
Jia, Weiju
Mao, Chengliang
[J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 818

← 1 2 3 4 →