Influence of the Coarse Grain Structure of a Titanium Alloy Ti-4Al-3V Formed by Wire-Feed Electron Beam Additive Manufacturing on Strain Inhomogeneities and Fracture

被引：3
|
作者：
Klimenov, Vasily [1 ]
Kolubaev, Evgeny [2 ]
Anatoly, Klopotov [3 ]
Chumaevskii, Andrey [2 ]
Ustinov, Artem [3 ]
Strelkova, Irina [1 ]
Rubtsov, Valery [2 ]
Gurianov, Denis [2 ]
Han, Zeli [1 ]
Nikonov, Sergey [2 ]
Batranin, Andrey [1 ]
Khimich, Margarita [2 ]
机构：
[1] Natl Res Tomsk Polytech Univ, Div Mat Sci SAMT TPU, Lenina pr 30, Tomsk 634050, Russia
[2] Russian Acad Sci, Inst Strength Phys & Mat Sci, Siberian Branch, Akademicheskiy pr 2-4, Tomsk 634055, Russia
[3] Tomsk State Univ Architecture & Bldg, Dept Appl Mech & Mat Sci, Solyanaya Sq 2, Tomsk 634003, Russia
来源：
MATERIALS | 2023年 / 16卷 / 11期
关键词：
additive manufacturing; electron beam; titanium alloy; macrostructure; microstructure; mechanical properties; tomography; non-destructive testing; MECHANICAL-PROPERTIES; MICROSTRUCTURE; TI-6AL-4V;
D O I：
10.3390/ma16113901
中图分类号：
O64 [物理化学（理论化学）、化学物理学];
学科分类号：
070304 ; 081704 ;
摘要：
In this work, based on the multilevel approach, the features of the structure and properties of titanium alloy, formed during high-performance additive manufacturing by wire-feed electron beam technology, were studied. Methods of non-destructive X-ray control and tomography, along with optical and scanning electron microscopy, were used to study the structure at different scale levels of the sample material. The mechanical properties of the material under stress were revealed via the simultaneous observation of the peculiarities of deformation development, using a Vic 3D laser scanning unit. Using microstructural and macrostructural data, as well as fractography, the interrelations of structure and material properties caused by the technological features of the printing process and the composition of used welding wire were revealed.
引用
收藏
页数：22
相关论文
共 50 条
  • [21] Heat Input Effect on the Structure of ZhS6U Alloy Products Produced by Wire-Feed Electron-Beam Additive Manufacturing
    Gurianov, D. A.
    Fortuna, S. V.
    Nikonov, S. Yu.
    Moskvichev, E. N.
    Kolubaev, E. A.
    RUSSIAN PHYSICS JOURNAL, 2021, 64 (08) : 1415 - 1421
  • [22] Heat Input Effect on the Structure of ZhS6U Alloy Products Produced by Wire-Feed Electron-Beam Additive Manufacturing
    D. A. Gurianov
    S. V. Fortuna
    S. Yu. Nikonov
    E. N. Moskvichev
    E. A. Kolubaev
    Russian Physics Journal, 2021, 64 : 1415 - 1421
  • [23] Structure and Phase Composition of Ti-6Al-4V Alloy Obtained by Electron-Beam Additive Manufacturing
    Utyaganova, V. R.
    Vorontsov, A. V.
    Eliseev, A. A.
    Osipovich, K. S.
    Kalashnikov, K. N.
    Savchenko, N. L.
    Rubtsov, V. E.
    Kolubaev, E. A.
    RUSSIAN PHYSICS JOURNAL, 2019, 62 (08) : 1461 - 1468
  • [24] Formation of Defects and Inhomogeneities in the Structure of Composite Materials Based on Aluminum-Manganese Bronze with an In Situ Introduction of Nickel and Titanium Alloys or Steel During Wire-Feed Electron Beam Additive Manufacturing
    Chumaevskii, A. V.
    Zykova, A. P.
    Osipovich, K. S.
    Dobrovolskii, A. R.
    Panfilov, A. O.
    Cheremnov, A. M.
    Nikolaeva, A. V.
    Gusarova, A. V.
    Nikonov, S. Yu.
    Semenchuk, V. M.
    Rubtsov, V. E.
    Kolubaev, E. A.
    RUSSIAN PHYSICS JOURNAL, 2023, 66 (10) : 1069 - 1076
  • [25] Formation of Defects and Inhomogeneities in the Structure of Composite Materials Based on Aluminum-Manganese Bronze with an In Situ Introduction of Nickel and Titanium Alloys or Steel During Wire-Feed Electron Beam Additive Manufacturing
    A. V. Chumaevskii
    A. P. Zykova
    K. S. Osipovich
    A. R. Dobrovolskii
    A. O. Panfilov
    A. M. Cheremnov
    A. V. Nikolaeva
    A. V. Gusarova
    S. Yu. Nikonov
    V. M. Semenchuk
    V. E. Rubtsov
    E. A. Kolubaev
    Russian Physics Journal, 2023, 66 : 1069 - 1076
  • [26] Two-Scale Computational Analysis of Deformation and Fracture in an Al-Si Composite Material Fabricated by Electron Beam Wire-Feed Additive Manufacturing
    Balokhonov, Ruslan
    Zemlianov, Aleksandr
    Utyaganova, Veronika
    Gatiyatullina, Diana
    Romanova, Varvara
    METALS, 2023, 13 (08)
  • [27] Additive Manufacturing of Titanium Aluminide Alloy Ti–Al–V–Nb–Cr–Gd by Selective Electron Beam Melting
    P. V. Panin
    E. A. Lukina
    I. A. Bogachev
    P. N. Medvedev
    S. A. Naprienko
    Metallurgist, 2023, 67 : 324 - 337
  • [28] Controlling the porosity using exponential decay heat input regimes during electron beam wire-feed additive manufacturing of Al-Mg alloy
    V. R. Utyaganova
    Andrey V. Filippov
    N. N. Shamarin
    A. V. Vorontsov
    N. L. Savchenko
    S. V. Fortuna
    D. A. Gurianov
    A. V. Chumaevskii
    V. E. Rubtsov
    S. Yu. Tarasov
    The International Journal of Advanced Manufacturing Technology, 2020, 108 : 2823 - 2838
  • [29] Effect of annealing heat treatment on microstructure and corrosion behavior of Ti6Al4V alloy fabricated by multi-laser beam wire-feed additive manufacturing in vacuum environment
    Ding, Xueping
    Ma, Honglin
    Zhang, Qi
    Yang, Jie
    Li, Daoyuan
    Fan, Shuqian
    JOURNAL OF ALLOYS AND COMPOUNDS, 2022, 914
  • [30] Controlling the porosity using exponential decay heat input regimes during electron beam wire-feed additive manufacturing of Al-Mg alloy
    Utyaganova, V. R.
    Filippov, Andrey, V
    Shamarin, N. N.
    Vorontsov, A. V.
    Savchenko, N. L.
    Fortuna, S., V
    Gurianov, D. A.
    Chumaevskii, A., V
    Rubtsov, V. E.
    Tarasov, S. Yu
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 108 (9-10): : 2823 - 2838
12345