Structural Optimization of AerMet100 Steel Torsion Spring Based on Strain Fatigue

被引:1
|
作者
Wang, Meng [1 ,2 ]
Li, Hongen [3 ]
Chen, Hu [4 ]
Fang, Xingbo [1 ,2 ]
Zhu, Enze [3 ]
Huang, Pujiang [1 ,2 ]
Wei, Xiaohui [1 ,2 ]
Nie, Hong [1 ,2 ]
机构
[1] Nanjing Univ Aeronaut & Astronaut, Key Lab Fundamental Sci, Natl Def Adv Design Technol Flight Vehicle, Nanjing 210016, Peoples R China
[2] Nanjing Univ Aeronaut & Astronaut, State Key Lab Mech & Control Mech Struct, Nanjing 210016, Peoples R China
[3] Shenyang Inst Aircraft Design, Shenyang 110035, Peoples R China
[4] Nanjing Univ Aeronaut & Astronaut, Coll Gen Aviat & Flight, Liyang 213300, Peoples R China
基金
中国国家自然科学基金;
关键词
ultra-high-strength steel; torsion spring; strain fatigue; structural optimization; FEM;
D O I
10.3390/aerospace10100828
中图分类号
V [航空、航天];
学科分类号
08 ; 0825 ;
摘要
The torsion spring of a carrier-based aircraft landing gear is a key component, which is normally manufactured out of AerMet100 ultra-high-strength steel. The takeoff and landing performance is greatly influenced by its bearing capacity and structural durability. To carry out the structure anti-fatigue design, it is necessary to investigate the influence of the spring structure features on its fatigue life, based on which the strain fatigue analysis and parameter optimization design of the torsion spring are executed. Through the finite element analysis conducted with ABAQUS, it was determined that there exists serious stress concentration in the relief groove. Based on the theory of strain fatigue, the fatigue life of the torsion spring was obtained, and the fracture position and lifecycle were consistent with the test results. A structure optimization platform based on a parametric method was established. Samples were selected through the DOE (design of experiment), and a surrogate model was established based on RBF (radial basis functions), followed by optimization using MIGA (multi-island genetic algorithms). With the parameter optimization of the relief groove, the structure was reconstituted and reanalyzed. From the simulation results, the peak strain was reduced by 30.7%, while the fatigue life was increased by 86.2% under the same loads and constraints. Moreover, laboratory tests were performed on the torsion spring after reconstruction, which showed that the fatigue life increases by 85.6% after optimization. The method presented in this paper can provide theoretical support and technical guidance for the application and structural optimization of ultra-high-strength steel structures.
引用
收藏
页数:16
相关论文
共 50 条
  • [21] High temperature electropalsticity in Aermet100 steel by decoupling electron wind effect
    Wang, Yu
    Deng, Taiqing
    Chang, Xusheng
    Qi, Yushi
    Chen, Gang
    Chen, Qiang
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2024, 915
  • [22] Microstructures and tensile properties of laser cladded AerMet100 steel coating on 300 M steel
    Liu, Jian
    Li, Jia
    Cheng, Xu
    Wang, Huaming
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2018, 34 (04) : 643 - 652
  • [23] Effects of microstructures on the fatigue crack growth behavior of laser additive manufactured ultrahigh-strength AerMet100 steel
    Ran, Xian-zhe
    Liu, Dong
    Li, Jia
    Wang, Hua-ming
    Cheng, Xu
    Zhang, Ji-kui
    Tang, Hai-bo
    Liu, Xiao
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 721 : 251 - 262
  • [24] Microstructural investigation and mechanical performance of laser cladding repaired bainite steel with AerMet100 steel
    Zhang, Bo
    He, Bei
    Wang, Huaming
    SURFACE & COATINGS TECHNOLOGY, 2022, 440
  • [25] Analytical modeling of residual stresses in laser-assisted milling AerMet100 steel
    Zeng, Haohao
    Hu, Xiangtao
    Yang, Dong
    OPTICS AND LASER TECHNOLOGY, 2023, 158
  • [26] Microstructure and properties of micro-arc oxidation ceramic films on AerMet100 steel
    Wang, WeiZhan
    Feng, ShunShan
    Li, ZhongMing
    Chen, ZhiGang
    Zhao, TaiYong
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2020, 9 (03): : 6014 - 6027
  • [27] 3D FEM simulation of hot extrusion process of AerMet100 Steel
    Chen, Jun-Feng
    Yan, Mu-Fu
    Wang, Xiang-Rong
    Cailiao Rechuli Xuebao/Transactions of Materials and Heat Treatment, 2007, 28 (SUPPL.): : 367 - 370
  • [28] Prediction of the hot deformation behavior for Aermet100 steel using an artificial neural network
    Ji, Guoliang
    Li, Fuguo
    Li, Qinghua
    Li, Huiqu
    Li, Zhi
    COMPUTATIONAL MATERIALS SCIENCE, 2010, 48 (03) : 626 - 632
  • [29] Microstructures and tensile properties of laser cladded AerMet100 steel coating on 300M steel
    Jian Liu
    Jia Li
    Xu Cheng
    Huaming Wang
    Journal of Materials Science & Technology, 2018, 34 (04) : 643 - 652
  • [30] Analytical Modeling of White Layer Formation in Orthogonal Cutting of AerMet100 Steel Based on Phase Transformation Mechanism
    Zeng, Haohao
    Yan, Rong
    Hu, Tiantian
    Du, Pengle
    Wang, Wei
    Peng, Fangyu
    JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2019, 141 (06):