Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

被引：15

作者：

Zhou, You ^{[1
]}

Chang, Tianxing ^{[1
]}

Fang, Xuewei ^{[1
]}

Chen, Ruikai ^{[1
]}

Li, Yefei ^{[2
]}

Huang, Ke ^{[1
]}

机构：

[1] Xi An Jiao Tong Univ, Sch Mech Engn, State Key Lab Mfg Syst Engn, Xian 710049, Peoples R China

[2] Xi An Jiao Tong Univ, State Key Lab Mech Behav Mat, Xian 710049, Peoples R China

来源：

MATERIALS & DESIGN | 2023年 / 233卷

基金：

中国国家自然科学基金;

关键词：

Additive manufacturing; Aluminum alloy; Micro -alloying elements; Mechanical properties; Strengthening mechanisms; HYDROGEN MICROPORES; GROWTH-BEHAVIOR; ALUMINUM; PRECIPITATION; ZR; MICROSTRUCTURE; DEFORMATION; PARTICLES; STRENGTH; PHASE;

D O I：

10.1016/j.matdes.2023.112287

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In this study, a novel Sc/Zr/Ti/Er-modified 2219 aluminum alloy was designed and wall-shaped components were then fabricated by wire-arc directed energy deposition (DED). Due to the heterogeneous nucleation promoted by primary Al3X dispersoids, the as-deposited alloy exhibits a highly equiaxed fine grain structure. Two heat treatment schedules were conducted to tailor the strength and thermal stability of the alloy. Compared with the classical T6 heat treatment, the additional homogenization step before the T6 heat treatment (HT6) prefabricated more Al3X dispersoids, which indirectly promoted the transition from & theta;& DPRIME; precipitates to & theta;& PRIME; precipitates, resulting in a slight reduction in strength. However, this homogenization step helps to avoid the aggregation of pores by promoting pores ripening and significantly alleviates the anisotropy of ductility. In addition, the better thermal stability of the HT6 heat treated alloy is due to more Al3X dispersoids and finer & theta;& PRIME; precipitates with high coarsening resistance caused by the segregation of Sc and Mn at the & theta;& PRIME;/Al interface during thermal exposure. In general, the wire-arc DEDed micro-alloyed 2219 Al alloy exhibits a promising combination of strength and ductility after heat treatment and its mechanical properties are superior to those of the wrought micro-alloyed AlCu alloys.

引用

页数：14

共 66 条

[1] Additively manufactured novel Al-Cu-Sc-Zr alloy: Microstructure and mechanical properties [J].

Agrawal, Priyanka ;

Gupta, Sanya ;

Thapliyal, Saket ;

Shukla, Shivakant ;

Haridas, Ravi Sankar ;

Mishra, Rajiv S. .

ADDITIVE MANUFACTURING, 2021, 37

[2] Influence of deposition strategy and heat treatment on mechanical properties and microstructure of 2319 aluminium WAAM components [J].

Arana, Maider ;

Ukar, Eneko ;

Rodriguez, Iker ;

Aguilar, David ;

Alvarez, Pedro .

MATERIALS & DESIGN, 2022, 221

[3] Assessing the effect of TIG alternating current time cycle on aluminium wire plus arc additive manufacture [J].

Ayarkwa, K. F. ;

Williams, S. W. ;

Ding, J. .

ADDITIVE MANUFACTURING, 2017, 18 :186-193

[4]

Ayarkwa K. F., 2015, International Journal of Rapid Manufacturing, V5, P44

[5] Aging behavior and strengthening mechanisms of coarsening resistant metastable θ′ precipitates in an Al-Cu alloy [J].

Bahl, Sumit ;

Xiong, Lianghua ;

Allard, Lawrence F. ;

Michi, Richard A. ;

Poplawsky, Jonathan D. ;

Chuang, Andrew Chihpin ;

Singh, Dileep ;

Watkins, Thomas R. ;

Shin, Dongwon ;

Haynes, J. Allen ;

Shyam, Amit .

MATERIALS & DESIGN, 2021, 198

[6] Mechanical Properties and Fracture Behaviors of GTA-Additive Manufactured 2219-Al After an Especial Heat Treatment [J].

Bai, J. Y. ;

Fan, C. L. ;

Lin, S. B. ;

Yang, C. L. ;

Dong, B. L. .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2017, 26 (04) :1808-1816

[7] Structure and energetics of the coherent interface between the θ′ precipitate phase and aluminium in Al-Cu [J].

Bourgeois, Laure ;

Dwyer, Christian ;

Weyland, Matthew ;

Nie, Jian-Feng ;

Muddle, Barrington C. .

ACTA MATERIALIA, 2011, 59 (18) :7043-7050

[8] Wire and arc additive manufacturing of dissimilar 2319 and 5B06 aluminum alloys [J].

Chang, Tianxing ;

Fang, Xuewei ;

Liu, Gang ;

Zhang, Hongkai ;

Huang, Ke .

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2022, 124 :65-75

[9] Twinned dendrites growth in wire arc directed energy deposition of Al-Zn-Mg-Cu alloy [J].

Dong, Bolun ;

Cai, Xiaoyu ;

Chen, Fukang ;

Lin, Sanbao ;

Zong, Yingying ;

Shan, Debin .

MATERIALS & DESIGN, 2023, 228

[10] Effects of interlayer temperature on the microstructures of wire arc additive manufactured Al-Zn-Mg-Cu alloy: Insights into texture responses and dynamic precipitation behaviors [J].

Dong, Bolun ;

Cai, Xiaoyu ;

Xia, Yunhao ;

Lin, Sanbao ;

Fan, Chenglei ;

Chen, Fukang .

ADDITIVE MANUFACTURING, 2021, 48

← 1 2 3 4 5 6 7 →