Design optimization with genetic algorithm of open slotted axial flux permanent magnet generator for wind turbines

被引:1
作者
Huner, Engin [1 ]
Toylan, Hayrettin [2 ]
机构
[1] Univ Kirklareli, Fac Technol, Energy Syst Engn, Kirklareli, Turkey
[2] Univ Kirklareli, Fac Technol, Mechatron Engn Dept, Kirklareli, Turkey
关键词
Genetic algorithm; axial flux; finite element method; permanent magnet; optimization; MOTOR;
D O I
10.1080/15435075.2022.2057800
中图分类号
O414.1 [热力学];
学科分类号
摘要
In this study, the design parameters of Open Slotted Axial Flux Permanent Magnet (OSAFPM) Generator for wind turbines are presented using Genetic Algorithms (GA), an optimization algorithm based on natural selection and genetic mechanisms. Electromagnetic analysis of Open Slotted Axial Flux Permanent Magnet generator has been performed by using parameters optimized with Genetic Algorithms. The ANSYS Maxwell program, which uses the finite element method (FEM), has been used for electromagnetic analysis. Compared to ANSYS Maxwell, it is observed that the genetic algorithm significantly reduces the computational time required for design optimization. However, initial design and optimization with Genetic Algorithms have resulted by 8.94% increase in power densities. In addition, 12.71%, 38.62%, 62.02%, and 56.39% improvements have been obtained for air gap magnetic flux density, flux linkage, induced voltage, and current waveforms, respectively. This suggests that optimization with a Genetic algorithm improves the Open Slotted Axial Flux Permanent Magnet generator parameters.
引用
收藏
页码:423 / 431
页数:9
相关论文
共 21 条
[1]  
Ayçiçek E, 2012, SIGMA J ENG NAT SCI, V30, P392
[2]  
Aydin M, 2003, IEEE IND APPLIC SOC, P555
[3]   Taguchi Approach for Optimization of Parameters that Reduce Dimensional Variation in Investment Casting [J].
Bansode, S. N. ;
Phalle, V. M. ;
Mantha, S. .
ARCHIVES OF FOUNDRY ENGINEERING, 2019, 19 (01) :5-12
[4]   Design Optimization of Direct-Coupled Ironless Axial Flux Permanent Magnet Synchronous Wind Generator With Low Cost and High Annual Energy Yield [J].
Daghigh, Ali ;
Javadi, Hamid ;
Torkaman, Hossein .
IEEE TRANSACTIONS ON MAGNETICS, 2016, 52 (09)
[5]   Cogging Torque Minimization Using Skewed and Separated Magnet Geometries [J].
Dalcali, Adem ;
Kurt, Erol ;
Celik, Emre ;
Ozturk, Nihat .
JOURNAL OF POLYTECHNIC-POLITEKNIK DERGISI, 2020, 23 (01) :223-230
[6]   Design and optimization of in-wheel asynchronous motor for electric vehicle [J].
Demir, Ugur ;
Aluner, Mustafa Caner .
JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2018, 33 (04) :1517-1530
[7]   USING TAGUCHI METHOD IN DEFINING CRITICAL ROTOR POLE DATA OF LSPMSM CONSIDERING THE POWER FACTOR AND EFFICIENCY [J].
Demir, Ugur ;
Akuner, Mustafa Caner .
TEHNICKI VJESNIK-TECHNICAL GAZETTE, 2017, 24 (02) :347-353
[8]   A general approach to sizing and power density equations for comparison of electrical machines [J].
Huang, SR ;
Luo, J ;
Leonardi, F ;
Lipo, TA .
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, 1998, 34 (01) :92-97
[9]   Optimization of axial flux permanent magnet generator by Taguchi experimental method [J].
Huner, E. .
BULLETIN OF THE POLISH ACADEMY OF SCIENCES-TECHNICAL SCIENCES, 2020, 68 (03) :409-419
[10]  
Joorabian Mahmood, 2009, 2009 4th IEEE Conference on Industrial Electronics and Applications, P524, DOI 10.1109/ICIEA.2009.5138261