Influence of Friction Stir Processing on the Friction, Wear and Corrosion Mechanisms of Solid-State Additively Manufactured 316L Duplex Stainless Steel

被引：36
作者：
Ralls, Alessandro M. [1 ]
Daroonparvar, Mohammedreza [1 ,3 ]
Kasar, Ashish K. [1 ]
Misra, Manoranjan [2 ]
Menezes, Pradeep L. [1 ]
机构：
[1] Univ Nevada Reno, Dept Mech Engn, Reno, NV 89557 USA
[2] Univ Nevada, Dept Mat & Chem Engn, Reno, NV 89557 USA
[3] ASB Ind, Res & Dev Dept, Barberton, OH 44203 USA
来源：
TRIBOLOGY INTERNATIONAL | 2023年 / 178卷
基金：
美国国家科学基金会;
关键词：
Tribology; Corrosion; Cold Spray; Friction Stir Processing; METAL-MATRIX COMPOSITES; ELASTIC-MODULUS; HEAT-TREATMENT; COLD; MICROSTRUCTURE; BEHAVIOR; PERFORMANCE; RESISTANCE; RECRYSTALLIZATION; EVOLUTION;
D O I：
10.1016/j.triboint.2022.108033
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Friction stir processing (FSP) was employed as a post-surface processing technique to modify the tribological and corrosion behavior of cold-sprayed (CS) 316L SS deposits. Results indicate that the effect of FSP induced an austenitic phase transformation due to the combination of frictional heat and plastic deformation. Consequentially, the friction of the CS deposit after FSP decreased by 8.3%. Similarly, the wear rate was reduced by 55.1%. These properties were improved mostly due to the closure of pores (yielding a 99.97% density) and localized grain refinement. Electrochemical measurements revealed that the corrosion rate was reduced by similar to 65%. Also, the pitting corrosion resistance (Epit - Ecorr) increased, which can be majorly attributed to the densified surface and full austenitic phase transformation after FSP. Compared to the other samples, the highest polarization resistance at the corrosion potential (Rpol) was obtained for the FSP CS 316L SS. Based on these findings, it can be inferred that FSP is a viable method to improve the tribological and corrosion behavior of CS 316L SS deposits.
引用
收藏
页数：17
相关论文
共 107 条
[11]   Imposed potential measurements to evaluate the pitting corrosion resistance and the galvanic behaviour of a highly alloyed austenitic stainless steel and its weldment in a LiBr solution at temperatures up to 150 °C [J].
Blasco-Tamarit, E. ;
Garcia-Garcia, D. M. ;
Garcia Anton, J. .
CORROSION SCIENCE, 2011, 53 (02) :784-795
[12]   The connections between powder variability and coating microstructures for cold spray deposition of austenitic stainless steel [J].
Brewer, L. N. ;
Schiel, J. F. ;
Menon, E. S. K. ;
Woo, D. J. .
SURFACE & COATINGS TECHNOLOGY, 2018, 334 :50-60
[13]   Passivation evolution of Ti -Ta-Nb medium-entropy sputtered thin films in sulfuric acid solution [J].
Chen, W. Y. ;
Chen, Y. H. ;
Li, W. P. ;
Zhou, Rui ;
Chou, T. H. ;
Wang, X. ;
Huang, J. C. .
APPLIED SURFACE SCIENCE, 2022, 576
[14]   Dependence of adhesion and friction on porosity in porous anodic alumina films [J].
Choi, Dukhyun ;
Lee, Sangmin ;
Kim, Seonghan ;
Lee, Pyungsoo ;
Lee, Kunhong ;
Park, Hyunchul ;
Hwang, Woonbong .
SCRIPTA MATERIALIA, 2008, 58 (10) :870-873
[15]  
Corrosion PAS, 2018, ENG HDB
[16]   Electrochemical studies on the effect of residual stress on the corrosion of 316L manufactured by selective laser melting [J].
Cruz, V. ;
Chao, Q. ;
Birbilis, N. ;
Fabijanic, D. ;
Hodgson, P. D. ;
Thomas, S. .
CORROSION SCIENCE, 2020, 164
[17]   Microstructural evolution and mechanical properties of the stir zone in friction stir processed AISI201 stainless steel [J].
Cui, H. B. ;
Xie, G. M. ;
Luo, Z. A. ;
Ma, J. ;
Wang, G. D. ;
Misra, R. D. K. .
MATERIALS & DESIGN, 2016, 106 :463-475
[18]   Modification of surface hardness, wear resistance and corrosion resistance of cold spray Al coated AZ31B Mg alloy using cold spray double layered Ta/Ti coating in 3.5 wt % NaCl solution [J].
Daroonparvar, M. ;
Khan, M. U. Farooq ;
Saadeh, Y. ;
Kay, C. M. ;
Kasar, A. K. ;
Kumar, P. ;
Esteves, L. ;
Misra, M. ;
Menezes, P. ;
Kalvala, P. R. ;
Bakhsheshi-Rad, H. R. ;
Gupta, R. K. .
CORROSION SCIENCE, 2020, 176
[19]   Enhanced corrosion resistance and surface bioactivity of AZ31B Mg alloy by high pressure cold sprayed monolayer Ti and bilayer Ta/Ti coatings in simulated body fluid [J].
Daroonparvar, M. ;
Khan, M. U. Farooq ;
Saadeh, Y. ;
Kay, C. M. ;
Gupta, R. K. ;
Kasar, A. K. ;
Kumar, P. ;
Misra, M. ;
Menezes, Pradeep L. ;
Bakhsheshi-Rad, H. R. .
MATERIALS CHEMISTRY AND PHYSICS, 2020, 256
[20]   Improvement of Wear, Pitting Corrosion Resistance and Repassivation Ability of Mg-Based Alloys Using High Pressure Cold Sprayed (HPCS) Commercially Pure-Titanium Coatings [J].
Daroonparvar, Mohammadreza ;
Kasar, Ashish K. ;
Farooq Khan, Mohammad Umar ;
L. Menezes, Pradeep ;
Kay, Charles M. ;
Misra, Manoranjan ;
Gupta, Rajeev K. .
COATINGS, 2021, 11 (01) :1-20
12345678910