Analysis of the effect of thermocycling on bonding cements to zirconia

被引:8
作者
Alrabeah, Ghada [1 ]
Alomar, Sadeem [2 ]
Almutairi, Azizah [2 ]
Alali, Hafsah [2 ]
Arrejaie, Aws [1 ]
机构
[1] King Saud Univ, Coll Dent, Dept Prosthet Dent Sci, Riyadh, Saudi Arabia
[2] King Saud Univ, Coll Dent, Dent Interns, Riyadh, Saudi Arabia
关键词
Shear bond strength; Resin cements; Zirconia ceramics; Thermocycling; RESIN CEMENT; STRENGTH; DEGRADATION; COMPOSITES;
D O I
10.1016/j.sdentj.2023.07.009
中图分类号
R78 [口腔科学];
学科分类号
1003 ;
摘要
Objective: The aim of this study was to evaluate the effect of thermocycling on shear bond strength (SBS) of several resin cement materials to different types of zirconia dental ceramics.Materials and Methods: 120 square shaped disc specimens were fabricated using two types of zirconia blocks (Sagemax and Sirona). Each zirconia group was divided into three sub-groups based on the resin cement bonded to the specimens. Three different self-adhesive resin cements were used (Calibra, Breeze and RelyX). The specimens were further grouped into experimental and control groups (n = 10). The experimental specimens were exposed to a thermo-cycling protocol of 1500 cycles in water bath at 5c and 55c. Specimens were then stored at 37c for 24 h then all specimens underwent SBS test with an Instron machine. Mode of failure was inspected visually and microscopically. Data were statistically analyzed using multivariate analysis of variance followed by one-way analysis of variance, Tukey's multiple comparison test, student's t-test for independent samples were used to compare the mean values of SBS in relation to the categorical study variables.Results: The mean SBS values of experimental groups were significantly lower than control groups for all the 6 combinations of Zirconia and cement types (p < 0.0001). The higher mean difference (14.29 MPa) was observed in the combination of Sagemax and Rely-X. Rely-X displayed the highest SBS among all the cements while no significant difference was found in mean SBS values of Calibra and Breez cements in all groups. The mean SBS values of Sagemax zirconia were significantly higher than the Sirona with all three types of cements (p < 0.0001) within control groups. Microscopic and visual analysis demonstrated a majority of adhesive mode of failure.Conclusion: Thermocycling significantly reduced the SBS between the zirconia materials and self-adhesive resin cements tested. The amount of reduction varies according to cement and zirconia types.(c) 2023 The Authors. Production and hosting by Elsevier B.V. on behalf of King Saud University This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
引用
收藏
页码:734 / 740
页数:7
相关论文
共 28 条
[1]  
Abhishek Gopala, 2022, J Clin Exp Dent, V14, pe316, DOI [10.4317/jced.59324, 10.4317/jced.59324]
[2]   Effect of Home Bleaching on the Optical Properties and Surface Roughness of Novel Aesthetic Dental Ceramics [J].
Alrabeah, Ghada ;
Shabib, Sara ;
Almomen, Rhma ;
Alhedeithi, Nura ;
Alotaibi, Sarah ;
Habib, Syed Rashid .
COATINGS, 2023, 13 (02)
[3]   Assessment of in vitro methods used to promote adhesive interface degradation: A critical review [J].
Amaral, Flavia L. B. ;
Colucci, Vivian ;
Palma-Dibb, Regina G. ;
Corona, Silmara A. M. .
JOURNAL OF ESTHETIC AND RESTORATIVE DENTISTRY, 2007, 19 (06) :340-353
[4]  
Blatz MB, 2007, QUINTESSENCE INT, V38, P745
[5]   Scaling, dimensional analysis, and indentation measurements [J].
Cheng, YT ;
Cheng, CM .
MATERIALS SCIENCE & ENGINEERING R-REPORTS, 2004, 44 (4-5) :91-149
[6]   STABILITY OF THE BOND BETWEEN TWO RESIN CEMENTS AND AN YTTRIA-STABILIZED ZIRCONIA CERAMIC AFTER SIX MONTHS OF AGING IN WATER [J].
da Silva, Eduardo M. ;
Miragaya, Luciana ;
Sabrosa, Carlos Eduardo ;
Maia, Lucianne C. .
JOURNAL OF PROSTHETIC DENTISTRY, 2014, 112 (03) :568-575
[7]  
Dalla Lana Mattiello Rodrigo, 2013, ISRN Biomaterials, DOI 10.5402/2013/185376
[8]   THE FRACTURE-TOUGHNESS OF REPAIRED COMPOSITE [J].
DHURU, VB ;
LLOYD, CH .
JOURNAL OF ORAL REHABILITATION, 1986, 13 (05) :413-421
[9]   Thermal cycling procedures for laboratory testing of dental restorations [J].
Gale, MS ;
Darvell, BW .
JOURNAL OF DENTISTRY, 1999, 27 (02) :89-99
[10]  
ISO. International Standards Organization, 1996, Amendment ISO 10477