Optimization of Performance Parameters of Phase Frequency Detector Using Taguchi DoE and Pareto ANOVA Techniques

被引:4
作者
Sharma, Jyoti [1 ]
Sharma, Gaurav Kumar [2 ]
Varma, Tarun [3 ]
Boolchandani, Dharmendar [3 ]
机构
[1] Malaviya Natl Inst Technol, Birla Inst Technol, ECE Dept, Jaipur 302017, Rajasthan, India
[2] GLA Univ, ECE Dept, Mathura 281406, Uttar Pradesh, India
[3] Malaviya Natl Inst Technol, ECE Dept, Jaipur 302017, Rajasthan, India
关键词
Phase frequency detector (PFD); optimization; Taguchi DoE; Pareto ANOVA; maximum operating frequency; phase noise; power dissipation; Cadence; Minitab software; MINIMAL BLIND ZONE; PLL; DESIGN; PFD;
D O I
10.1142/S021812662350158X
中图分类号
TP3 [计算技术、计算机技术];
学科分类号
0812 ;
摘要
This paper utilizes Taguchi design of experiments and Pareto analysis of variance statistical approaches to demonstrate circuit optimization. The phase-frequency detector (PFD) circuit based on dynamic logic has been chosen for optimization. For various MOSFETs of PFD, three levels and three factors of power supply and width of PMOS and NMOS (V-DD, w(p), and w(n)) are considered to be critical performance governing factors. The Taguchi technique determines the level of significance of a factor that influences a given performance parameter. The crucial factor for a given response is determined via ANOVA analysis. The optimum values for the parameters V-DD, w(p), and w(n )are likewise determined using this procedure to maximize the circuit's overall performance. Taguchi DoE and Pareto Anova analyses have been performed using the Minitab software. Simulating the circuit with GPDK 180nm CMOS technology using these methods ensures that the acquired parameters are correct for best performance. The Cadence Virtuoso tool has been used to conduct pre-layout and post-layout simulations. The simulation outcomes are reasonably close to the ANOVA predicted result. Phase noise, power dissipation, and frequency of operation of the proposed PFD are -159.56dBc/Hz, 9.83 mu W, and 10.21GHz, respectively, and it occupies a chip area of 300.41 mu m(2). The proposed PFD is used to implement a charge-pump PLL which performs effectively with a settling time of 2.59 mu s.
引用
收藏
页数:19
相关论文
共 50 条
  • [31] Bioslurry phase remediation of chlorpyrifos contaminated soil: Process evaluation and optimization by Taguchi design of experimental (DOE) methodology
    Mohan, S. Venkata
    Sirisha, K.
    Rao, R. Sreenivasa
    Sarma, P. N.
    ECOTOXICOLOGY AND ENVIRONMENTAL SAFETY, 2007, 68 (02) : 252 - 262
  • [32] Optimization and evaluation of dry and minimum quantity lubricating methods on machinability of AISI 4140 using Taguchi design and ANOVA
    Gurbuz, Huseyin
    Emre Gonulacar, Yunus
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2021, 235 (07) : 1211 - 1227
  • [33] Effect of waste matrix for the optimization of moisture content and calorific value of biodried material using Taguchi DOE
    Mohammed, Mutala
    Ozbay, Ismail
    Karademir, Aykan
    Donkor, Augustine
    DRYING TECHNOLOGY, 2019, 37 (11) : 1352 - 1362
  • [34] Parameter optimization in milling of glass fiber reinforced plastic (GFRP) using DOE-Taguchi method
    Ghalme, Sachin
    Mankar, Ankush
    Bhalerao, Y. J.
    SPRINGERPLUS, 2016, 5
  • [35] Effect of process variation on the performance of phase frequency detector
    Venugopal, Nandakumar P.
    Shastry, Nihal
    Upadhyaya, Shambhu J.
    21ST IEEE INTERNATIONAL SYMPOSIUM ON DEFECT AND FAULT-TOLERANCE IN VLSI SYSTEMS, PROCEEDINGS, 2006, : 525 - +
  • [36] Optimization of Constrained Layer Damping Parameters in Beam Using Taguchi Method
    K. S. K. Sasikumar
    K. P. Arulshri
    S. Selvakumar
    Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, 2017, 41 : 243 - 250
  • [37] Optimization of process parameters for biodegradation of malathion by Micrococcus aloeverae MAGK3 using Taguchi methodology and metabolic pathway analysis
    Dar, Mohd Ashraf
    Kaushik, Garima
    BIOCATALYSIS AND AGRICULTURAL BIOTECHNOLOGY, 2022, 42
  • [38] Optimization of Constrained Layer Damping Parameters in Beam Using Taguchi Method
    Sasikumar, K. S. K.
    Arulshri, K. P.
    Selvakumar, S.
    IRANIAN JOURNAL OF SCIENCE AND TECHNOLOGY-TRANSACTIONS OF MECHANICAL ENGINEERING, 2017, 41 (03) : 243 - 250
  • [39] Optimization of Drilling Parameters of Fabricated GFRP Composite using Taguchi Method
    Nanubala, Niranjan
    Yadav, Mahesh J.
    Danduk, Chaitanya
    Subbu, S. Kanmani
    2016 INTERNATIONAL CONFERENCE ON ENERGY EFFICIENT TECHNOLOGIES FOR SUSTAINABILITY (ICEETS), 2016, : 881 - 885
  • [40] Optimization of machining parameters in rotary EDM process by using the Taguchi method
    E. Aliakbari
    H. Baseri
    The International Journal of Advanced Manufacturing Technology, 2012, 62 : 1041 - 1053