Microstructural and Mechanical Properties of Hot Deformed AISI 4340 Steel Produced by Powder Metallurgy

被引：10

作者：

Yirik, Ayse Gozde ^{[1
]}

Gunduez, Sueleyman ^{[1
]}

Tastemur, Demet ^{[1
]}

Erden, Mehmet Akif ^{[2
]}

机构：

[1] Karabuk Univ, Technnol Fac, Dept Mfg Engn, TR-78050 Karabuk, Turkiye

[2] Karabuk Univ, Engn Fac, Biomed Engn, TR-78050 Karabuk, Turkiye

来源：

SCIENCE OF SINTERING | 2023年 / 55卷 / 01期

关键词：

Microalloyed Steel; Powder Metallurgy; Thermomechanical Processing; Mechanical Properties; MEDIUM-CARBON; BEHAVIOR;

D O I：

10.2298/SOS2301045Y

中图分类号：

TQ174 [陶瓷工业]; TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

In this work, AISI 4340 steel was produced by powder metallurgy. Samples were sintered at 1150oC for 90 min. and then cooled in the furnace. Except to those in the as -sintered condition, one of the produced samples was homogenized at 1150oC for 1 h and then cooled in air. Other samples were deformed at the temperature range of 1150-930oC and deformation rate of 30 and 60% followed by cooling in sand, air and water mediums. The grain size gradually decreased depending on the deformation rate or cooling rate in AISI 4340 steel. Small grains occurred due to completely recrystallization at 60% deformation rate. Density and hardness also increased by the increase in deformation rate. The results showed that hot deformation is a process that is capable of improving the properties of AISI 4340 steel produced by powder metallurgy without rising the addition of alloying elements.

引用

页码：45 / 56

页数：12

共 43 条

[1] Effect of Hot Pressing and Reinforcement of TiC and WC on the Mechanical Properties and Microstructure of AlCuFeCrNi HEAs Alloy [J].

Akkas, Mehmet ;

Al Sudani, Fatimah Ridha Abbood .

SCIENCE OF SINTERING, 2021, 53 (01) :19-35

[2] Tribological and Aging Behavior of Hybrid Al 7075 Composite Reinforced with B4C, SiC, and TiB2 [J].

Aksoz, S. ;

Kaner, S. ;

Kaplan, Y. .

SCIENCE OF SINTERING, 2021, 53 (03) :311-321

[3]

Askeland D.R., 1996, SCI ENG MAT

[4]

Avsar E, 2010, J FAC ENG ARCHIT GAZ, V25, P713

[5]

Aydin Y.A. M., 2011, Production Methods and Manufacturing Technologies

[6]

Baksan B, 2003, METALURGY I, P1

[7]

Brian James W., 1987, MAT DES, V8, P187, DOI [10.1016/0261-3069(87)90133-6, DOI 10.1016/0261-3069(87)90133-6]

[8] Microstructure and Mechanical Properties of Ni Matrix B4C Reinforced Functionally Graded Composites [J].

Caligulu, Ugur ;

Durmus, Hulya ;

Akkas, Mehmet ;

Sahin, Baris .

SCIENCE OF SINTERING, 2021, 53 (04) :475-484

[9]

Callister W.D., 2007, Material Science and Enginering, An Introduction, V7

[10]

Dizdar S., 2012, GEAR TECHNOL, P60

← 1 2 3 4 5 →