Optimization of Cutting Parameters for Face Milling Titanium Alloy Using MQL

被引：0
|
作者：
AHMED Hassan
姚振强
机构：
[1] Department of Manufacturing and Automation Shanghai Jiaotong University Shanghai 200030
[2] Department of Manufacturing and Automation Shanghai Jiaotong University Shanghai 200030
来源：
Journal of DongHua University | 2005年 / 02期
关键词：
Taguchi method; milling; titanium alloy; MQL;
D O I：
10.19884/j.1672-5220.2005.02.003
中图分类号：
TG580.6 [磨削加工工艺];
学科分类号：
080201 ; 080503 ;
摘要：
When using MQL as a cooling technique, many parameters have to be adjusted. The Taguchi method was used in this study to investigate the cutting characteristics of face milling of titanium alloys using PVD-coated inserts. To find the optimal volume removed and surface roughness, an orthogonal array, the signal-to-noise (S/N) ratio and the analysis of variance (ANOVA) were employed. The optimum cutting parameters was obtained. Throughout this study, it was found that the feed rate is the most influencing cutting parameter in the face milling of titanium alloys.
引用
收藏
页码：9 / 12
页数：4
相关论文
共 50 条
  • [11] Multi-objective optimization in the milling of titanium alloys using the MQL technique
    Hassan, A
    Yao, ZQ
    JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION, 2004, 19 (04): : 26 - 29
  • [12] Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under MQL Condition using TOPSIS and ANOVA Analysis
    Van Canh Nguyen
    Thuy Duong Nguyen
    Dung Hoang Tien
    ENGINEERING TECHNOLOGY & APPLIED SCIENCE RESEARCH, 2021, 11 (01) : 6775 - 6780
  • [13] Multi-objective optimization in the milling of titanium alloys using the MQL technique
    Ahmed Hassan
    Yao Zhen-qiang
    Journal of Wuhan University of Technology-Mater. Sci. Ed., 2004, 19 : 26 - 29
  • [14] Modeling of machined surface roughness and optimization of cutting parameters in face milling
    Bajic, D.
    Lela, B.
    Zivkovic, D.
    METALURGIJA, 2008, 47 (04): : 331 - 334
  • [15] Optimization of cutting parameters with Taguchi and grey relational analysis methods in MQL-assisted face milling of AISI O2 steel
    Kursuncu, Bilal
    Biyik, Yasin Ensar
    JOURNAL OF CENTRAL SOUTH UNIVERSITY, 2021, 28 (01) : 112 - 125
  • [16] Modelling and Optimization of the Cutting Parameters for the Milling Operation of Titanium Alloy (Ti6Al4V)
    Ilesanmi, Daniyan
    Thlabadira, Isaac
    Phokobye, Solomon
    Mrausi, Siviwe
    Mpofu, Khumbulani
    Masu, Leonard
    PROCEEDINGS OF 2020 IEEE 11TH INTERNATIONAL CONFERENCE ON MECHANICAL AND INTELLIGENT MANUFACTURING TECHNOLOGIES (ICMIMT 2020), 2020, : 68 - 72
  • [17] Fuzzy Optimization of Cutting Parameters for Titanium Alloy's Machining
    Chen, Jianling
    Li, Jianfeng
    Sun, Jie
    2008 4TH INTERNATIONAL CONFERENCE ON WIRELESS COMMUNICATIONS, NETWORKING AND MOBILE COMPUTING, VOLS 1-31, 2008, : 10952 - 10955
  • [18] Experimental analysis and optimization of cutting parameters for end milling aluminium alloy
    Ahmad, Nafis
    Wakabayashi, Ryo
    Tomohisa, Tanaka
    Saito, Yoshio
    TOWARDS SYNTHESIS OF MICRO - /NANO - SYSTEMS, 2007, (05): : 347 - +
  • [19] A coupling method of response surfaces (CRSM) for cutting parameters optimization in machining titanium alloy under minimum quantity lubrication (MQL) condition
    ZhiQiang Liu
    Jinyang Xu
    Shu Han
    Ming Chen
    International Journal of Precision Engineering and Manufacturing, 2013, 14 : 693 - 702
  • [20] A coupling method of response surfaces (CRSM) for cutting parameters optimization in machining titanium alloy under minimum quantity lubrication (MQL) condition
    Liu, ZhiQiang
    Xu, Jinyang
    Han, Shu
    Chen, Ming
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2013, 14 (05) : 693 - 702
12345