Optimization of Cutting Parameters for Face Milling Titanium Alloy Using MQL

被引：0
|
作者：
AHMED Hassan
姚振强
机构：
[1] Department of Manufacturing and Automation Shanghai Jiaotong University Shanghai 200030
[2] Department of Manufacturing and Automation Shanghai Jiaotong University Shanghai 200030
来源：
Journal of DongHua University | 2005年 / 02期
关键词：
Taguchi method; milling; titanium alloy; MQL;
D O I：
10.19884/j.1672-5220.2005.02.003
中图分类号：
TG580.6 [磨削加工工艺];
学科分类号：
080201 ; 080503 ;
摘要：
When using MQL as a cooling technique, many parameters have to be adjusted. The Taguchi method was used in this study to investigate the cutting characteristics of face milling of titanium alloys using PVD-coated inserts. To find the optimal volume removed and surface roughness, an orthogonal array, the signal-to-noise (S/N) ratio and the analysis of variance (ANOVA) were employed. The optimum cutting parameters was obtained. Throughout this study, it was found that the feed rate is the most influencing cutting parameter in the face milling of titanium alloys.
引用
收藏
页码：9 / 12
页数：4
相关论文
共 50 条
  • [1] Optimization of cutting parameters for face milling titanium alloy using MQL
    Ahmed, Hassan
    Yao, Zhen-Qiang
    Journal of Dong Hua University (English Edition), 2005, 22 (02): : 9 - 12
  • [2] Investigation of MQL parameters in milling of titanium alloy
    Zan, Zhuoliang
    Guo, Kai
    Sun, Jie
    Wei, Xin
    Tan, Yecheng
    Yang, Bin
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 116 (1-2): : 375 - 388
  • [3] Investigation of MQL parameters in milling of titanium alloy
    Zhuoliang Zan
    Kai Guo
    Jie Sun
    Xin Wei
    Yecheng Tan
    Bin Yang
    The International Journal of Advanced Manufacturing Technology, 2021, 116 : 375 - 388
  • [4] Robust Multiobjective Optimization of Cutting Parameters in Face Milling
    Aykut, Seref
    Kentli, Aykut
    Gulmez, Servet
    Yazicioglu, Osman
    ACTA POLYTECHNICA HUNGARICA, 2012, 9 (04) : 85 - 100
  • [5] Modeling and optimization of cutting process parameters in face milling of EN 31 alloy steel using nanoparticle fluids
    Singh, Talvinder
    Sharma, Vijay Kumar
    Rana, Mohit
    Saini, Abhineet
    Deorari, Rajesh
    Dixit, Anil Kumar
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2024, 10 (03) : 1523 - 1535
  • [6] EFFECT OF THE MQL TECHNIQUE ON CUTTING FORCE AND SURFACE QUALITY DURING THE SLOT MILLING OF TITANIUM ALLOY
    Osman, Khaled Ali
    Yilmaz, Volkan
    Unver, Hakki Ozgur
    Seker, Ulvi
    Kilic, S. Engin
    MATERIALI IN TEHNOLOGIJE, 2022, 56 (01): : 3 - 10
  • [7] Performance Investigation of MQL Parameters Using Nano Cutting Fluids in Hard Milling
    Tran Minh Duc
    Tran The Long
    Ngo Minh Tuan
    FLUIDS, 2021, 6 (07)
  • [8] An investigation into the surface integrity and cutting force characteristics in titanium alloy end milling using soluble oil and MQL as coolants
    Mohandas, K. N.
    Hosamani, Basavaraj
    Nagaraju
    Kemminje, Vignesh
    Raju, V. R.
    Nagahanumaiah
    RESULTS IN SURFACES AND INTERFACES, 2024, 17
  • [9] Multi response optimization of nozzle process parameters in MQL assisted face milling of AISI 52,100 alloy steel using TGRA
    Rana, Mohit
    Singh, Talvinder
    Saini, Abhineet
    Singh, Jaswinder
    Sharma, Vijay Kumar
    Singh, Maninderjeet
    Rooprai, Ranbir Singh
    MATERIALS TODAY-PROCEEDINGS, 2021, 44 : 3177 - 3182
  • [10] Multi-objective Optimization in the Milling of Titanium Alloys Using the MQL Technique
    艾哈迈德
    Journal of Wuhan University of Technology-Materials Science, 2004, (04) : 26 - 29
12345