Effect of Ce-base mischmetal addition on the microstructure and mechanical properties of hot-rolled ZK60 alloy

被引：1

作者：

E.P.Silva ^{[1
,2
]}

R.H.Buzolin ^{[3
,4
]}

F.Marques ^{[2
]}

F.Soldera ^{[5
]}

U.Alfaro ^{[6
]}

H.C.Pinto ^{[2
]}

机构：

[1] Institute of Engineering, Science and Technology (IECT), Federal University of Vales do Jequitinhonha e Mucuri (UFVJM)

[2] S?o Carlos School of Engineering (EESC), University of S?o Paulo (USP), Department of Materials Engineering

[3] Christian Doppler Laboratory for Design of high-performance alloys by thermomechanical processing

[4] Technische Universit?t Graz (TU Graz), Institute of Materials Science, Joining and Forming

[5] Institute of Functional Materials, Department of Materials Science and Engineering, Saarland University

[6] German Aerospace Center (DLR) Institute of Materials Research

来源：

Journal of Magnesium and Alloys | 2021年 / 9卷 / 03期

基金：

巴西圣保罗研究基金会;

关键词：

D O I：

暂无

中图分类号：

TG146.22 [];

学科分类号：

080502 ;

摘要：

Mg-Zn-Zr (ZK) alloys exhibit notably high mechanical strength amongst all magnesium alloy grades.However,due to the formation of low melting point Mg3Zn7-precipitates,these alloys are susceptible to hot cracking,thus compromising their metallurgical processing.The addition of rare earths to ZK alloys is an alternative to form higher melting point intermetallic compounds,speed up dynamic recrystallization,refine grain size,enhance corrosion resistance and extend the service temperature due to improved creep resistance.This work deals with the effect of Ce-base mischmetal addition on the hot rolling behaviour of as-cast ZK60 alloy.The microstructure investigation conducted using electron microscopy and X-Ray diffraction shows that precipitation of Mg7Zn3intermetallics occur during hot rolling,whereas no further precipitation is observed for the ZK60-Mm alloys.The fragmentation of the intermetallic compounds occur during hot rolling and finer particles of Mg7Zn3are observed for the ZK60,whereas Mg7Zn3and Mg Zn2Ce intermetallics are formed in the alloy modified with mischmetal addition.A higher fraction of dynamically recrystallized grains is observed for the ZK60-Mm in comparison to the ZK60.Continuous recrystallization takes place in ZK60 with the formation of sub-grains near to the intermetallics and the addition of mischmetal promotes the occurrence of discontinuous recrystallization with the nucleation of new grains close to the precipitates.The mechanical strength and,in particular,the ductility of the hot-rolled alloys are notably improved when compared to the same alloys in the as-cast condition.The mechanical strength is,however,higher for the ZK60 alloy.Less solid solution strengthening,softer Mg Zn2Ce intermetallics and more extensive recrystallization contribute to reduce the mechanical strength of ZK60-Mm.Failure in both alloys are initiated at coarse intermetallics and propagate through intermetallic-rich regions.

引用

页码：995 / 1006

页数：12

共 38 条

[1] Modeling of continuous dynamic recrystallization of Al-Zn-Cu-Mg alloy during hot deformation based on the internal-state-variable （ISV） method[J] . Z.C. Sun,H.L. Wu,J. Cao,Z.K. Yin.International Journal of Plasticity . 2018
[2] Impact of Ce-base mischmetal on the microstructure and mechanical behavior of ZK60 magnesium casting alloys[J] . E.P. Silva,F. Marques,T.S. Nossa,U. Alfaro,H.C. Pinto.Materials Science ＆ Engineering A . 2018
[3] On the role of twinning and stacking faults on the crystal plasticity and grain refinement in magnesium alloys[J] . S.Q. Zhu,Simon P. Ringer.Acta Materialia . 2018
[4] A review of dynamic recrystallization phenomena in metallic materials[J] . K. Huang,R.E. Logé.Materials ＆ Design . 2016
[5] Effect of Mischmetal Additions and Solution Heat Treatments （T4） on the Microstructure and Mechanical Properties of Thixocast ZK60-RE Magnesium Alloys[J] . da Silva Erenilton Pereira,Buzolin Ricardo Henrique,Callegari Bruna,Warchomicka Fernando,Requena Guillermo C.,Pinto Haroldo Cavalcanti.Materials Science Forum . 2016 (879-)
[6] Thermodynamic modeling of the Y–Mg–Zn, Gd–Mg–Zn, Tb–Mg–Zn, Dy–Mg–Zn, Ho–Mg–Zn, Er–Mg–Zn, Tm–Mg–Zn and Lu–Mg-Zn systems[J] . Zhijun Zhu,Arthur D. Pelton.Journal of Alloys and Compounds . 2015
[7] Gradient crystal plasticity including dislocation-based work-hardening and dislocation transport[J] . Stephan Wulfinghoff,Thomas B?hlke.International Journal of Plasticity . 2015
[8] Casting in the Semi-Solid State of ZK60 Magnesium Alloy Modified with Rare Earth Addition[J] . E.P. Silva,Larissa Fernandes Batista,Bruna Callegari,Ivan Feierabend,Ricardo Henrique Buzolin,Rodrigo Santiago Coelho,Fernando Warchomicka,Guillermo C. Requena,Haroldo Pinto.Advanced Materials Research . 2014 (922-)
[9] Effects of minor Gd addition on microstructures and mechanical properties of the high strain-rate rolled Mg–Zn–Zr alloys[J] . Haiyang Yu,Yan Hongge,Chen Jihua,Su Bin,Zheng Yi,Shen Yanjin,Ma Zhaojie.Journal of Alloys and Compounds . 2014
[10] Influence of rolling temperature on the microstructure and mechanical properties of Mg–Gd–Y–Zn–Zr alloy sheets[J] . C. Xu,M.Y. Zheng,K. Wu,E.D. Wang,G.H. Fan,S.W. Xu,S. Kamado,X.D. Liu,G.J. Wang,X.Y. Lv.Materials Science ＆ Engineering A . 2013

← 1 2 3 4 →