Dynamic Recrystallization Behavior of 13%Cr Martensitic Stainless Steel under Hot Working Condition

被引：1
|
作者：
G.R.Ebrahimi [1 ]
H.Keshmiri [2 ]
A.R.Maldar [2 ]
A.Momeni [3 ]
机构：
[1] Metallurgical and Materials Engineering Department,Ferdowsi University of Mashhad,Mashhad 9177948974,Iran
[2] Department of Materials Engineering,Sabzevar Tarbiat Moallem University,Sabzevar 9617976487,Iran
[3] Materials Science and Engineering Department,Hamedan University of Technology,Hamedan 6516913418,Iran
来源：
Journal of Materials Science & Technology | 2012年 / 28卷 / 05期
关键词：
Hot deformation; Dynamic recrystallization; Critical strain;
D O I：
暂无
中图分类号：
TG142.71 [不锈钢、耐酸钢];
学科分类号：
摘要：
In this study,the effect of hot deformation on martensitic stainless steel was carried out in temperatures between 950 to 1100℃and strain rates of 0.001,0.01 and 0.1 s-1.Two important dynamic recrystallization parameters,the critical strain and the point of maximum dynamic softening,were derived from strain hardening rate vs stress curves.Then the calculated parameters were used to predict the dynamic recrystallized fraction.Our results show that critical stress and strain increase with decreasing deformation temperature and increasing strain rate.The hot deformation activation energy of the steel is also investigated in the present work with 413 kJ/mol.Our experimental flow curves are in fair agreement with the kinetics of dynamic recrystallization model.
引用
收藏
页码：467 / 473
页数：7
相关论文
共 50 条
  • [1] Dynamic Recrystallization Behavior of 13%Cr Martensitic Stainless Steel under Hot Working Condition
    Ebrahimi, G. R.
    Keshmiri, H.
    Maldar, A. R.
    Momeni, A.
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2012, 28 (05) : 467 - 473
  • [2] Investigation on Dynamic Recrystallization Behavior of Martensitic Stainless Steel
    Ren, Facai
    Chen, Fei
    Chen, Jun
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2014, 2014
  • [3] Dynamic Recrystallization Behavior of AISI 420 Stainless Steel under Hot Compression
    Cao, Y.
    Di, H. S.
    Misra, R. D. K.
    HIGH TEMPERATURE MATERIALS AND PROCESSES, 2015, 34 (02) : 155 - 161
  • [4] Modeling the Flow Curve Characteristics of 410 Martensitic Stainless Steel Under Hot Working Condition
    Momeni, Amir
    Dehghani, Kamran
    Ebrahimi, Golam Reza
    Keshmiri, Hamid
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2010, 41A (11): : 2898 - 2904
  • [5] Modeling the Flow Curve Characteristics of 410 Martensitic Stainless Steel Under Hot Working Condition
    Amir Momeni
    Kamran Dehghani
    Golam Reza Ebrahimi
    Hamid Keshmiri
    Metallurgical and Materials Transactions A, 2010, 41 : 2898 - 2904
  • [6] HOT WORKABILITY OF 13%Cr MARTENSITIC STAINLESS STEEL FOR OCTG.
    Ohtsubo, Hiroshi
    Togashi, Fusao
    Kawasaki, Tetsuo
    Takada, Isao
    Transactions of the Iron and Steel Institute of Japan, 1983, 24 (04)
  • [7] Improvement of impact toughness by modified hot working and heat treatment in 13%Cr martensitic stainless steel
    Srivatsa, Kulkarni
    Srinivas, Perla
    Balachandran, G.
    Balasubramanian, V.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 677 : 240 - 251
  • [8] Dynamic recrystallization behavior and constitutive analysis of Incoloy 901 under hot working condition
    Momeni, A.
    Abbasi, S. M.
    Morakabati, M.
    Badri, H.
    Wang, X.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 615 : 51 - 60
  • [9] Effect of Nitrogen on the Hot Deformation Behavior of 0.4C-13Cr Martensitic Stainless Steel
    Liu, Weijian
    Li, Jing
    Li, Shouhui
    Li, Jihui
    Li, Xuejun
    STEEL RESEARCH INTERNATIONAL, 2021, 92 (08)
  • [10] Dynamic Recrystallization and Precipitation in 13Cr Super-Martensitic Stainless Steels
    Gholam Reza Ebrahimi
    Amir Momeni
    Mohammad Jahazi
    Philippe Bocher
    Metallurgical and Materials Transactions A, 2014, 45 : 2219 - 2231
12345