Optimizing the delamination failure in bamboo fiber reinforced polyester composite

被引：70

作者：

Abilash N. ^{[1
]}

Sivapragash M. ^{[1
]}

机构：

[1] Department of Mechanical Engineering, N.I. University, Kumaracoil, 629180, Tamilnadu

来源：

Journal of King Saud University - Engineering Sciences | 2016年 / 28卷 / 01期

关键词：

Bamboo natural fibers; Delamination; FRP composites; Grey; Polyester; Taguchi;

D O I：

10.1016/j.jksues.2013.09.004

中图分类号：

学科分类号：

摘要：

Delamination is represented to be the most prevalent failure in composite structures. The use of composites in the manufacturing sector plays a very important role in the industry in general. Moreover these materials have unique characteristics when analyzed separately from constituents which are a part of them. In this paper, a partially ecological composite was made, using natural fibers as reinforcement (bamboo fiber), in the polyester resin matrix to form a composite, seeking to improve the mechanical behavior among its class of materials. The characteristics of a composite material are determined by how it behaves while machining, Drilling is the most predominant machining process because of its cost effectiveness when compared with other processes. Obviously delamination is the major problem that is focused by many researchers while selecting drilling as the machining process in polymeric composites. This research mainly emphasizes on the critical parameters by varying its speed, feed, and diameter of the cutting tool, their contribution to delamination was analyzed. Reduced delaminations were identified by varying the speed and feed rate. © 2013

引用

页码：92 / 102

页数：10

共 19 条

[1]

Navin chand, Et al., Anisotropic abrasive wear behaviour of bamboo (Dentrocalamus strictus), Wear, 262, pp. 1031-1037, (2007)

[2]

Rashdi A., Water absorption behaviour of kenaf reinforced unsaturated polyester composites and its influence on their mechanical properties, Pertanika J. Sci. Technol., 18, 2, pp. 433-440, (2010)

[3]

Basavarajappa, Et al., Effect of filler materials on dry sliding wear behavior of polymer matrix composites – a taguchi approach, J. Miner. Mater. Character. Eng., 8, 5, pp. 379-391, (2009)

[4]

Yuhazri M., Et al., Mechanical properties of kenaf/polyester composites, Int. J. Eng. Technol. IJET-IJENS, 11, 1, (2011)

[5]

Gaitonde, Et al., Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites, J. Mater. Process. Technol., 203, pp. 431-438, (2008)

[6]

Rubio C., Effects of high speed in the drilling of glass fiber reinforced plastic: evaluation of the delamination factor, Int. J. Mach. Tools Manuf., 48, pp. 715-720, (2008)

[7]

Khashaba, Delamination in drilling GFR-thermoset composites, Compos. Struct., 63, pp. 313-327, (2004)

[8]

Capello E., Workpiece damping and its effect on delamination damage in drilling thin composite laminates, J. Mater. Process. Technol., 148, pp. 186-195, (2004)

[9]

Valadez-Gonzalez, Et al., Effect of fiber surface treatment on the fiber-matrix bond strength of natural fiber reinforced composites, Compos. Part B, 30, pp. 309-320, (1999)

[10]

Mohana, Et al., Delamination analysis in drilling process of glass fiber reinforced plastic (GFRP) composite materials, J. Mater. Process. Technol., 186, pp. 265-271, (2007)

← 1 2 →