Analysis of the adhesive layer of laser weld bonding joints in dual phase steel/ aluminum alloy

被引：8

作者：

Zhou D. ^{[1
]}

Li N. ^{[1
]}

Xu S. ^{[1
]}

Liu J. ^{[1
]}

机构：

[1] State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Hunan University, Changsha

来源：

Jixie Gongcheng Xuebao/Journal of Mechanical Engineering | 2016年 / 52卷 / 14期

关键词：

Adhesive layer; Laser weld bonding; Shearing force; Spectra; Weld molding;

D O I：

10.3901/JME.2016.14.025

中图分类号：

学科分类号：

摘要：

Through comparison analysis of the laser weld bonding and laser welding of dual phase steel to aluminum alloy, the adhesive layer action of its effect on dissimilar metals in steel-on-aluminum overlap configuration are discussed. By collecting and analyzing plasma shape and welding spectra, it is found that the color of plasma with high density induced by laser weld bonding is bright, a certain angle is formed between plasma and the sample surface, the surface of aluminum alloy with high reflectivity is improved by the decomposition products of adhesive layer, thus laser energy absorbed by plasma is reduced. However, the relative intensity of spectra and electron density of plasma is increased, which shows that laser energy absorption rate is increased by adding adhesive layer. The adhesive layer also has the effect of increasing weld penetration and width. The result of the shearing experiments shows that the average shear strength of welded joint increases compared to that without adhesive addition. Because of the upper dual phase steel layer with faster cooling rate, and laser energy absorption of the lower aluminum alloy increased, thus the diffusion from the lower Al to the upper steel side is suppressed, the volume fraction of Al on both sides of weld width increase, transverse area of steel and aluminum increase, the bonding rate is improved, in addition, the weld and adhesive layer undertake the shear load together, which can improve the mechanical properties of weld joint with adhesive addition. © 2016 Journal of Mechanical Engineering.

引用

页码：25 / 30

页数：5

共 12 条

[1]

Liu C., Wang L., Liu Y., Development of advanced high-strength steel used for automobile and its application in body design, Special Steel Technology, 18, 2, pp. 1-9, (2012)

[2]

Fan Z., Gui L., Su R., Research and development of automotive lightweight technology, Journal of Automotive Safety and Energy Saving, 5, 1, pp. 1-16, (2014)

[3]

Zhang Y., Peng Y., Ma C., Et al., Welding harden quenching tendency and cold cracking sensitivity of Q890 high strength steel, Trans. China Weld Inst., 34, 6, pp. 53-55, (2013)

[4]

Chen Y., Modern Laser Welding Technology, (2006)

[5]

Robert W., Messler, Weld-bonding:The best or worst of two processes, Industrial Robot, 29, 2, pp. 138-148, (2002)

[6]

Liu L.M., Wang H.Y., The effect of the adhesive on the microcracks in the laser welded bonding Mg to Al joint, Materials Science and Engineering A, 507, 1-2, pp. 22-28, (2009)

[7]

Liu L., Wang H., Wang H., Et al., Microstructural characteristics and mechanical properties of laser weld bonded joints in magnesium alloy, China Mechanical Engineering, 18, 3, pp. 352-356, (2007)

[8]

Liu L., Review of magnesium alloy welding, 14th National Conference on Welding, pp. 18-23, (2010)

[9]

Zhou D., Dai T., Xu S., Et al., Microstructure and properties of galvanized steel/aluminum alloy laser-adhesive hybrid bonding, The Chinese Journal of Nonferrous Metals, 24, 7, pp. 1736-1743, (2014)

[10]

Ren D., Liu L., Analysis of the adhesive layer of laser weld bonding joints in magnesium alloy, Journal of Mechanical Engineering, 45, 8, pp. 266-269, (2009)

← 1 2 →