Microstructural Evolution and Mechanical Properties of a Medium-Manganese Steel Manufactured by Laser-Based Powder Bed Fusion of Metals

被引：0

作者：

Huebner, Leoni ^{[1
]}

Koeksal, Bugra ^{[2
]}

Wegener, Thomas ^{[1
]}

Haase, Christian ^{[3
,4
]}

Niendorf, Thomas ^{[1
]}

机构：

[1] Univ Kassel, Inst Mat Engn Met Mat, Moenchebergstr 3, D-34125 Kassel, Germany

[2] Rhein Westfal TH Aachen, Steel Inst IEHK, Intzestr 1, D-52072 Aachen, Germany

[3] TU Berlin, Chair Mat Addit Mfg, Ernst Reuter Pl 1, D-10587 Berlin, Germany

[4] TU Berlin, Ctr 3D Technol, Str 17 Juni 136, D-10623 Berlin, Germany

来源：

ADVANCED ENGINEERING MATERIALS | 2025年

关键词：

additive manufacturing; laser-based powder bed fusion of metals; medium-manganese steels; retained austenite; transformation-induced plasticity; GRAIN-BOUNDARIES; DEFORMATION-BEHAVIOR; AUSTENITE REVERSION; MN; SEGREGATION; EMBRITTLEMENT; MARTENSITE; TOUGHNESS; PATHWAY; ALLOYS;

D O I：

10.1002/adem.202500886

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Medium-manganese steels (MMnS) represent novel third-generation advanced high-strength steels, which are characterized by Mn content between 3 and 12 wt% as well as a multiphase microstructure. These steels are well-known for outstanding combinations of high to ultrahigh strength at relatively high total elongation. Strength and ductility are significantly affected by the amount of retained austenite, its stability, and the related transformation-induced plasticity. Due to the possibility of microstructure design, laser-based powder bed fusion of metals (PBF-LB/M) is a promising processing method to tailor the mechanical performance of MMnS. In the present study, a Fe-12Mn-0.2C MMnS is manufactured by PBF-LB/M using blended powder as well as pre-alloyed powder to investigate the applicability of rapid alloy development. Various scanning speeds are used to determine the influence of energy deposition rate on microstructure and mechanical properties. Microstructural analysis of the different as-built conditions is carried out by optical and scanning electron microscopy, X-ray diffraction, and electron backscatter diffraction. The feasibility of using blended powder instead of atomized powder for preliminary experiments on PBF-LB/M-produced MMnS is discussed. In addition, a significant influence of process parameters on the resulting austenite fraction as well as strength and ductility for the investigated material is revealed.

引用

页数：10

共 45 条

[1]

alak A., 2012, Manganese in Powder Metallurgy Steels

[2] Intercritical annealing to achieve a positive strain-rate sensitivity of mechanical properties and suppression of macroscopic plastic instabilities in multi-phase medium-Mn steels [J].

Benzing, J. T. ;

Luecke, W. E. ;

Mates, S. P. ;

Ponge, D. ;

Raabe, D. ;

Wittig, J. E. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 803

[3] Multi-scale characterization of austenite reversion and martensite recovery in a cold-rolled medium-Mn steel [J].

Benzing, J. T. ;

da Silva, A. Kwiatkowski ;

Morsdorf, L. ;

Bentley, J. ;

Ponge, D. ;

Dutta, A. ;

Han, J. ;

McBride, J. R. ;

Van Leer, B. ;

Gault, B. ;

Raabe, D. ;

Wittig, J. E. .

ACTA MATERIALIA, 2019, 166 :512-530

[4]

Benzing J. T., 2018, Microsc. Microanal, V24, P2228

[5]

Bleck W., 2019, Berg Huettenmaenn Monatsh, V164, P466, DOI [10.1007/s00501-019-00904-y, DOI 10.1007/S00501-019-00904-Y]

[6] Driving Force and Logic of Development of Advanced High Strength Steels for Automotive Applications [J].

Bouaziz, Olivier ;

Zurob, Hatem ;

Huang, Mingxin .

STEEL RESEARCH INTERNATIONAL, 2013, 84 (10) :937-947

[7] Damage tolerant design by microstructural gradation - Influence of processing parameters and build orientation on crack growth within additively processed 316L [J].

Brenne, F. ;

Niendorf, T. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 764

[8] Creep and creep damage behavior of stainless steel 316L manufactured by laser powder bed fusion [J].

Calderon, L. A. Avila ;

Rehmer, B. ;

Schriever, S. ;

Ulbricht, A. ;

Jacome, L. Agudo ;

Sommer, K. ;

Mohr, G. ;

Skrotzki, B. ;

Evans, A. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 830

[9]

De Moor E., 2010, AIST T IRON STEEL TE, V7, P133

[10] Understanding Hot vs. Cold Rolled Medium Manganese Steel Deformation Behavior Using In Situ Microscopic Digital Image Correlation [J].

Dutta, Aniruddha ;

Ponge, Dirk ;

Sandloebes, Stefanie ;

Raabe, Dierk .

THERMEC 2018: 10TH INTERNATIONAL CONFERENCE ON PROCESSING AND MANUFACTURING OF ADVANCED MATERIALS, 2018, 941 :198-205

← 1 2 3 4 5 →