New insights into microstructure evolution and deformation mechanisms in additively manufactured 316L stainless steel

被引:0
作者
Barkia, Bassem [1 ]
Vallet, Maxime [2 ,3 ]
Tanguy, Alexandre [4 ]
Auger, Thierry [1 ]
Heripre, Eva [1 ]
机构
[1] Cnam, PIMM, Arts & Metiers, CNRS UMR 8006, 151 bd lHopital, F-75013 Paris, France
[2] Univ Paris Saclay, CentraleSupelec, CNRS, LMPS,ENS Paris Saclay,Lab Mecan Paris Saclay, F-91190 Gif Sur Yvette, France
[3] Univ Paris Saclay, CentraleSupelec, CNRS, SMPS,Lab Struct Proprietes & Modelisat Solides, F-91190 Gif Sur Yvette, France
[4] Ecole Polytech, Inst Polytech Paris, LMS, CNRS, Palaiseau, France
来源
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2025年 / 934卷
关键词
Additive manufacturing; Dislocation structure; Twinning; Work hardening; Austenitic stainless steel; PARTIAL DISLOCATION SEPARATION; HIGH-STRENGTH; STRESS; PLASTICITY; ORIGIN; SUBSTRUCTURE; DUCTILITY; BEHAVIOR; TEXTURE; NETWORK;
D O I
10.1016/j.msea.2025.148327
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
The evolution of the deformation micro-mechanisms and the dislocation structures in additively manufactured (AM) 316L steel was investigated via in-situ SEM/EBSD tensile tests coupled with fine TEM investigations at different strain levels. We show that the deformation mechanisms are strongly influenced by the initial dual-scale cellular structure, composed of large dislocation cells with chemically segregated cell walls, encapsulating smaller, chemically homogeneous internal regions. At low and medium strain levels, the primary deformation mode is dislocation slip across the dislocation cells interiors and formation of micro-bands while plastic deformation at higher strain is primarily controlled by mechanical nano-twins nucleated through the overlapping of stacking faults ribbons. Unlike conventional 316L, the AM 316L shows a nearly linear increase in dislocation density with increasing applied strain throughout the full range of plastic deformation. The initial cellular structure is preserved under plastic deformation, continuing to act as a barrier to dislocation glide and contributing to the high ductility of the AM 316L steel. A correlation between the work hardening rate and the observed deformation modes is evidenced, strengthening the conclusion that the plasticity of AM 316L is atypical. These findings enhance the understanding of the dislocation structures and the microstructure evolution during plastic deformation in AM 316L steel, providing valuable insights for the development of predictive largescale plasticity models for these materials.
引用
收藏
页数:12
相关论文
共 65 条
  • [1] Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe-Mn-C alloys
    Allain, S
    Chateau, JP
    Bouaziz, O
    Migot, S
    Guelton, N
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2004, 387 : 158 - 162
  • [2] Crystallographic aspects of geometrically-necessary and statistically-stored dislocation density
    Arsenlis, A
    Parks, DM
    [J]. ACTA MATERIALIA, 1999, 47 (05) : 1597 - 1611
  • [3] DEFORMATION OF PLASTICALLY NON-HOMOGENEOUS MATERIALS
    ASHBY, MF
    [J]. PHILOSOPHICAL MAGAZINE, 1970, 21 (170): : 399 - &
  • [4] Crack path and liquid metal embrittlement specificity of austenitic steels in mercury at room temperature
    Auger, Thierry
    Barkia, Bassem
    Heripre, Eva
    Michel, Vincent
    Mutel, Denis
    Guillot, Ivan
    Hamouche, Zehoua
    Medina-Almazan, Liliana
    [J]. SCRIPTA MATERIALIA, 2022, 215
  • [5] Non-equilibrium microstructure, crystallographic texture and morphological texture synergistically result in unusual mechanical properties of 3D printed 316L stainless steel
    Bahl, Sumit
    Mishra, Sumeet
    Yazar, K. U.
    Kola, Immanuel Raju
    Chatterjee, Kaushik
    Suwas, Satyam
    [J]. ADDITIVE MANUFACTURING, 2019, 28 : 65 - 77
  • [6] Steels in additive manufacturing: A review of their microstructure and properties
    Bajaj, P.
    Hariharan, A.
    Kini, A.
    Kuernsteiner, P.
    Raabe, D.
    Jaegle, E. A.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 772
  • [7] On the origin of the high tensile strength and ductility of additively manufactured 316L stainless steel: Multiscale investigation
    Barkia, Bassem
    Aubry, Pascal
    Haghi-Ashtiani, Paul
    Auger, Thierry
    Gosmain, Lionel
    Schuster, Frederic
    Maskrot, Hicham
    [J]. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2020, 41 : 209 - 218
  • [8] Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L
    Bertsch, K. M.
    de Bellefon, G. Meric
    Kuehl, B.
    Thoma, D. J.
    [J]. ACTA MATERIALIA, 2020, 199 (199) : 19 - 33
  • [9] On the stress dependence of partial dislocation separation and deformation microstructure in austenitic stainless steels
    Byun, TS
    [J]. ACTA MATERIALIA, 2003, 51 (11) : 3063 - 3071
  • [10] Caillard D., 2003, PERG MAT SER, V8, P3