Influence of build angle, printing layer thickness and aging on the flexural strength, precision, roughness and porosity analysis of a printed resin for provisional restorations

被引：1

作者：

Moreira, Fernanda Gurgel de Gois ^{[1
]}

Bezerra, Marcella Guedes Pereira Gouvea ^{[1
,5
]}

de Miranda, Larissa Mendonca ^{[1
]}

da Silva, Sarah Emille Gomes ^{[1
]}

Dantas, Eugenia Livia de Andrade ^{[2
]}

de Sousa, Frederico Barbosa ^{[3
]}

Ozcan, Mutlu ^{[4
]}

Souza, Rodrigo Othavio de Assuncao ^{[1
]}

机构：

[1] Fed Univ Rio Grande Norte UFRN, Dept Dent, Ave Salgado Filho Lagoa Nova,1787, BR-59056000 Natal, RN, Brazil

[2] Fed Univ Paraiba UFPB, Hlth Sci Ctr, Microscopy & Biol Imaging Lab, Joao Pessoa, Brazil

[3] Fed Univ Paraiba UFPB, Hlth Sci Ctr, Dept Morphol, Joao Pessoa, Brazil

[4] Univ Zurich, Ctr Dent Med, Zent Zahnmedizin, Clin Masticatory Disorders & Dent Biomat, Platten str,11, CH-8032 Zurich, Switzerland

[5] Fed Univ Paraiba UFPB, Dept Restorat Dent, Joao Pessoa, Brazil

来源：

ODONTOLOGY | 2025年 / 113卷 / 03期

关键词：

Printing; Three-dimensional; Flexural strength; Dental materials; MECHANICAL-PROPERTIES; SURFACE-ROUGHNESS; IN-VITRO; COLOR STABILITY; ACCURACY; POLYMERIZATION; ORIENTATION; TEMPERATURE; DIRECTION; ENERGY;

D O I：

10.1007/s10266-025-01060-1

中图分类号：

R78 [口腔科学];

学科分类号：

1003 ;

摘要：

Evaluate the impact of printing parameters on flexural strength (sigma), flexural modulus (E), precision, and surface topography characteristics of a resin used to produce provisional restorations. 450 bars for provisional restorations were printed using the SLA printing (25 x 2x2mm ISO-4049), and randomly divided into 30 groups (n = 15) according to the following factors: "printing layer thickness" (25 mu m;50 mu m;100 mu m), "Build angle" (0 degrees,30 degrees,45 degrees,60 degrees,90 degrees) and "thermocycling-TC" (with or without). Following printing, the samples underwent cleaning with isopropyl alcohol. Photopolymerization was performed for 15 min with an UV lamp. Subsequently, each bar was assessed using a digital caliper at 11 specific points in three dimensions for comparison with the STL file area for precision analysis. Half of the samples underwent thermocycling. All samples were submitted to the sigma test. Data for sigma (MPa), and (GPa) and precision (mm) were analyzed using 3 and 2-way ANOVA, respectively, and Tukey's post hoc test (5%). Micro-CT, 3D profilometry, and SEM were also performed and analyzed descriptively. The 90 degrees/25 mu mTC (63.0 +/- 4.5) showed the highest sigma, being only statistically similar to the 45 degrees/25 mu mTC (57.7 +/- 3.1). For precision 0 degrees/25 mu m (-2.56 +/- 0.04) expressed the greatest variation to the other experimental groups with a sample shrinkage of 25.6% compared to the STL file. The profilometry revealed that the 30 degrees/25 mu m group showed prominent peaks and valleys, presenting elevated roughness values with an average of Sa (28.25 mu m). Moreover, it was observed that the groups with a 60 degrees angle presented the lowest porosity values. A print layer thickness of 25 mu m combined with a build angle of 90 degrees and 45 degrees resulted in higher sigma and greater precision.

引用

页码：1165 / 1179

页数：15

共 65 条

[51] Printing accuracy, mechanical properties, surface characteristics, and microbial adhesion of 3D-printed resins with various printing orientations [J].