Microstructure and Mechanical Properties of Extruded Mg-2Sn-1.8Li-2Al-1Ag-0.5Zn Alloys

被引：0

作者：

Xu, Zhichao ^{[1
,2
,3
]}

Zhu, Yancheng ^{[2
]}

Song, Jie ^{[2
]}

Liu, Wei ^{[2
]}

Li, Jingren ^{[4
]}

Zhao, Hongliang ^{[1
]}

Zhu, Chang ^{[2
]}

Pan, Hucheng ^{[2
]}

Qin, Gaowu ^{[2
]}

机构：

[1] Zhengzhou Univ, Zhongyuan Crit Met Lab, Zhengzhou 450001, Peoples R China

[2] Northeastern Univ, Coll Mat Sci & Engn, Key Lab Anisotropy & Texture Mat, Minist Educ, Shenyang 110819, Peoples R China

[3] Henan Polytech Univ, Sch Mat Sci & Engn, Jiaozuo 454003, Peoples R China

[4] Liaoning Acad Mat, Inst Mat Plainificat, Shenyang 110164, Peoples R China

来源：

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2025年

基金：

中国国家自然科学基金;

关键词：

Mg alloy; microstructure; mechanical properties; strengthening mechanism; MG-SN ALLOYS; GRAIN-REFINEMENT; AL; ZN; STRENGTH; LI; CA; DEFORMATION; TEMPERATURE; EXTRUSION;

D O I：

10.1007/s11665-025-10727-3

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In this work, the microstructure and mechanical properties of as-extruded Mg-2Sn-1.8Li-2Al-1Ag-0.5Zn alloy (TLAQZ22211) were investigated, and it is found that the TLAQZ22211 alloy exhibited a bimodal grain structure after hot extrusion processing, with coarse elongated grains parallel to extrusion direction and fine grains surrounded. The yield strength (YS), ultimate tensile strength (UTS), and elongation (EL) of the TLAQZ22211 alloy extruded at 200 degrees C were measured at 295, 343 MPa, and 12.5%, respectively. The evolution of microstructure, changes in mechanical properties, and the influence of precipitation phase and dislocation on the properties of the alloy during deformation were discussed. The influence of dislocation-precipitation phase-interface synergistic strengthening effect on mechanical properties was compared and analyzed. The results showed that the high strength was mainly derived from the grain boundaries, nano-precipitations, and residual dislocations. And the good ductility can be attributed to the optimized bimodal grain structure and profuse low-angle grain boundaries (LAGBs) formed inside the elongated grains. The implementation of this work can provide guidance for the design and deformation of lightweight and high-strength magnesium alloys.

引用

页数：12

共 41 条

[1] Connections between the basal I1 "growth" fault and ⟨c plus a⟩ dislocations [J].

Agnew, S. R. ;

Capolungo, L. ;

Calhoun, C. A. .

ACTA MATERIALIA, 2015, 82 :255-265

[2] Effects of Zn and Ca addition on microstructure and mechanical properties of as-extruded Mg-1.0Sn alloy sheet [J].

Chai, Yanfu ;

Jiang, Bin ;

Song, Jiangfeng ;

Liu, Bo ;

Huang, Guangsheng ;

Zhang, Dingfei ;

Pan, Fusheng .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 746 (82-93) :82-93

[3] The role of low angle grain boundary in deformation of titanium and its size effect [J].

Chen, Sijing ;

Yu, Qian .

SCRIPTA MATERIALIA, 2019, 163 (148-151) :148-151

[4] Effect of Zn on microstructure and mechanical property of Mg-3Sn-1Al alloys [J].

Chen, Yu'an ;

Jin, Li ;

Song, Yu ;

Liu, Hao ;

Ye, Ruiyu .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2014, 612 :96-101

[5] Rational design of a lean magnesium-based alloy with high age-hardening response [J].

Cihova, M. ;

Schaeublin, R. ;

Hauser, L. B. ;

Gerstl, S. S. A. ;

Simson, C. ;

Uggowitzer, P. J. ;

Loeffler, J. F. .

ACTA MATERIALIA, 2018, 158 :214-229

[6] Age hardening responses of as-extruded Mg-2.5Sn-1.5Ca alloys with a wide range of Al concentration [J].

Huang, Qiuyan ;

Liu, Yang ;

Zhang, Aiyue ;

Jiang, Haoxin ;

Pan, Hucheng ;

Feng, Xiaohui ;

Yang, Changlin ;

Luo, Tianjiao ;

Li, Yingju ;

Yang, Yuansheng .

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2020, 38 :39-46

[7]

Huang ZQ., 2024, J Mater Eng Perform, V33, P1

[8] A new approach to grain refinement of an Mg-Li-Al cast alloy [J].

Jiang, B. ;

Qiu, D. ;

Zhang, M. -X. ;

Ding, P. D. ;

Gao, L. .

JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 492 (1-2) :95-98

[9] Comparative study regarding the effect of Al, Zn, and Gd on the microstructure and mechanical properties of Mg alloy Mg-Sn-Li [J].

Jiang, Yan ;

Chen, Yu'an ;

Gao, Junjie .

MATERIALS & DESIGN, 2016, 105 :34-40

[10] Influence of undissolved second-phase particles on dynamic recrystallization behavior of Mg-7Sn-1Al-1Zn alloy during low- and high-temperature extrusions [J].

Kim, Hyun Ji ;

Jin, Sang-Cheol ;

Jung, Jae-Gil ;

Park, Sung Hyuk .

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2021, 71 :87-97

← 1 2 3 4 5 →