Experimental study and numerical simulation of three dimensional two-phase impinging jet flow using anisotropic turbulence model

被引：0

作者：

Nazif H.R. ^{[1
]}

机构：

[1] Department of Mechanical Engineering, Imam Khomeini International University, Qazvin

来源：

Journal of Computational and Applied Research in Mechanical Engineering | 2020年 / 10卷 / 01期

关键词：

Anisotropy turbulence; Impinging jet; Two-phase flow; Wall function;

D O I：

10.22061/jcarme.2018.2981.1315

中图分类号：

学科分类号：

摘要：

Hydrodynamic of a turbulent impinging jet on a flat plate is studied experimentally and numerically. Experiments are conducted for the Reynolds number range of 72000 to 102000 and a fixed jet-to-plate dimensionless distance of H/d=3.5. Based on the experimental setup, a multi-phase numerical model is simulated to predict the flow properties of impinging jets using two turbulent models. Mesh-independency of the numerical model is studied to ensure the preciseness of the results. Numerical and experimental forces on the target plate are compared in order to examine the performance of turbulent models and wall functions. As a result, the force obtained by the Reynolds stress turbulent model alongside with non-equilibrium wall function is in good agreement with the experiment. The correlation equations are obtained for predicting the water thickness over the target plate and impingement force versus Reynolds number. It is also indicated that the maximum shear stress on the target plate is located at radial dimensionless distance of r/d=0.75. © 2020, Shahid Rajaee Teacher Tarining University (SRTTU). All rights reserved.

引用

页码：257 / 269

页数：12

共 31 条

[1]

Penumadu P. S., Rao A. G., Numerical investigations of heat transfer and pressure drop characteristics in multiple jet impingement system, Appl. Therm. Eng, 110, 1, pp. 1511-1524, (2017)

[2]

Cooper D., Jackson D. C., Launder B. E., Liao G. X., Impinging jet studies for turbulence model assessment, Int. J. Heat Mass Transf, 36, 10, pp. 2675-2684, (1993)

[3]

Lee D. H., Song J., Jo M. C., The effects of nozzle diameter on impinging jet heat transfer and fluid flow, J. Heat Transfer, 126, 4, (2004)

[4]

Alekseenko S. V., Markovich D. M., Electrodiffusion diagnostics of wall shear stresses in impinging jets, J. Appl. Electrochem, 24, 7, pp. 626-631, (1994)

[5]

Akansu Y. E., Sarioglu M., Kuvvet K., Yavuz T., Flow field and heat transfer characteristics in an oblique slot jet impinging on a flat plate, Int. Commun. Heat Mass Transf, 35, 7, pp. 873-880, (2008)

[6]

Meslem A., Et al., Flow dynamics and mass transfer in impinging circular jet at low Reynolds number. Comparison of convergent and orifice nozzles, Int. J. Heat Mass Transf, 67, 1, pp. 25-45, (2013)

[7]

Stevens J., Webb B. W., Measurements of flow structure in the stagnation impinging free-surface liquid jets, Int. J. Heat Mass Transf, 36, 17, pp. 4283-4286, (1993)

[8]

Modak M., Garg K., Srinivasan S., Sahu S. K., Theoretical and experimental study on heat transfer characteristics of normally impinging two dimensional jets on a hot surface, Int. J. Therm. Sci, 112, 1, pp. 174-187, (2017)

[9]

Katti V., Prabhu S. V., Experimental study and theoretical analysis of local heat transfer distribution between smooth flat surface and impinging air jet from a circular straight pipe nozzle, Int. J. Heat Mass Transf, 51, 1, pp. 4480-4495, (2008)

[10]

Coussirat M., Van Beeck J., Mestres M., Egusguiza E., Buchlin J. M., Escaler X., Computational fluid dynamics modeling of impinging gas-jet systems: I. assessment of eddy viscosity models, J. Fluids Eng, 127, 4, pp. 691-703, (2005)

← 1 2 3 4 →