STUDY ON TOOTH BEARING OF BEVEL GEARS. (1ST REPORT, THEORETICAL CALCULATION OF TOOTH BEARING AND EXPERIMENT).

被引：0

作者：

Terauchi, Yoshio ^{[1
]}

Nagamura, Kazuteru ^{[1
]}

Peng, Wen-Sheng ^{[1
]}

Sentoku, Hirofumi ^{[1
]}

机构：

[1] Hiroshima Univ, Hiroshima, Jpn, Hiroshima Univ, Hiroshima, Jpn

来源：

Bulletin of the JSME | 1986年 / 29卷 / 250期

关键词：

BEARINGS; -; Testing;

D O I：

10.1299/jsme1958.29.1294

中图分类号：

学科分类号：

摘要：

To make clear the relation between the tooth bearing of bevel gear and assembly errors quantitatively and theoretically, a theoretical calculation of tooth bearing was carried out for Gleason and Reinecker type straight bevel gears and for Reinecker type skew bevel gear considering the geometric tooth profile of these gears. And the tooth bearing of each bevel gear was also measured using a tooth bearing tester which was produced for this study. Comparison of the calculated tooth bearing with the experimental result confirmed the propriety of the present calculation method, and revealed the characteristic of tooth bearing of each gear.

引用

页码：1294 / 1302

共 50 条

[21] Study on the design of thin-shaped straight bevel gears. (2nd Report, numerical analyses of the effects of rim-web configuration upon the root stress distribution along the tooth trace)
Yokoyama, Masaaki, 1600, (55):
[22] STUDY ON THE DYNAMIC CHARACTERISTICS OF A WATER-LUBRICATED PUMP BEARING. (1ST REPORT, CYLINDRICAL BEARING UNDER HIGH AMBIENT PRESSURE).
Kanki, Hiroshi
Ozawa, Yutaka
Oda, Takanobu
Kawakami, Takashi
1824, (29):
[23] The development of pivot bearing with multiple degrees of freedom 1st report: Prototype of pivot bearing with two degrees of freedom
Noguchi, Shoji
Aramaki, Hirotoshi
Kanada, Tohru
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY, 2006, 30 (04): : 373 - 380
[24] STUDY ON RUNNING ACCURACY OF AN EXTERNALLY PRESSURIZED GAS THRUST BEARING (1ST REPORT, LOAD CAPACITY FLUCTUATION DUE TO MACHINING ERRORS OF THE BEARING).
Yabe, Hiroshi
Watanabe, Naoki
Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 1987, 53 (495): : 2360 - 2366
[25] AN UNUSUAL PRIMARY 1ST MOLAR IMPACTION ASSOCIATED WITH A SUPERNUMERARY TOOTH - CASE-REPORT
CHEN, HS
LIEU, JD
AUSTRALIAN DENTAL JOURNAL, 1993, 38 (04) : 277 - 279
[26] INVESTIGATION ABOUT THE PREVENTION OF TOOTH PROFILE CHANGE OF PLASTIC GEARS (1ST REPORT; AMOUNT OF PROFILE MODIFICATION OF STEEL GEAR, WHICH MESHED WITH NYLON GEAR).
Tsukamoto, Naohisa
Shi, Jiasun
1600, (28):
[27] Bending load capacity enhancement using an asymmetric tooth profile - (1st report, influences of pressure angle on tooth root stress and bending stiffness)
Deng, G
Nakanishi, T
Inoue, K
JSME INTERNATIONAL JOURNAL SERIES C-MECHANICAL SYSTEMS MACHINE ELEMENTS AND MANUFACTURING, 2003, 46 (03) : 1171 - 1177
[28] A study on thermal characteristics of a spiral grooved journal bearing (1st report, the case of steady and concentric operation)
Hirayama, Tomoko
Yamashita, Tsuyoshi
Yabe, Hiroshi
Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 2002, 68 (06): : 1883 - 1890
[29] STUDY ON STRENGTH DESIGN METHODS OF PLASTIC GEARS (1ST REPORT, CALCULATION METHOD OF FATIGUE STRENGTH DUE TO STRAIN ENERGY).
Tsukamoto, Naohisa
Taki, Tokihiko
Nishida, Noriteru
Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 1987, 53 (486): : 432 - 435
[30] IMPACT RESPONSE OF ROTOR-BEARING SYSTEM TO AN ARBITRARY EXCITATION OF PEDESTALS. (1ST REPORT: COMPARISON OF LINEAR ANALYSIS WITH EXPERIMENT).
Koike, Harutaka
Ishihara, Kunihiko
1783, (26):

← 1 2 3 4 5 →